background image

2-1

2. Precautions

Linear Bushing

2.  

Precautions on Use

2-1 

 

Safety Related Warning Displays

This manual uses the following safety related warning displays. Descriptions containing safety 
related warning displays are serious and must be followed. The Linear Bushing is a precision 
part, to be handled with care based on the following information.

  Warning

"A matter which, if mishandled, could result in 

death or serious injury."   

  Caution

"A matter which, if mishandled, could result in 

physical injury or material damage."   

 "Prohibited (never do this)"   

 "Required (always do this)"  

2-2 

 Handling

C A U T I O N

Do not disassemble

 

z

Disassembling components may cause dust to enter the system or degrade mounting 
accuracy of parts. Do not disassemble the product.

Falling objects

 

z

Take care not to drop or strike the Linear Bushing. This could cause injury and damage the 
product. If the product receives an impact, it could impair the product's functions, even if the 
product looks intact.

Handle with care

 

z

When handling the product, wear safety gloves and safety boots, etc., as appropriate to 
ensure safety.

www.thk.ru

тел. +7(499) 703-39-86

sales@thk.ru

Summary of Contents for Linear Bushing



















Reviews: