background image

11

ENGLISH

Your receiver is already programmed to receive the most important satellite signals.  You

can, however, change the programming or add new channels at any time.
To store a new channel in memory, you need the following information (found in specialist
satellite TV magazines):

1. LNB selection

3. Video frequency

and ToneBurst signal

4. Audio mode

2. Polarisation

5. Audio frequency

First, select the programme number you wish to assign to the new channel, and then follow

the instructions.

1. Selection of LNB and of ToneBurst signal

You can connect 2 LNBs to your receiver (e.g. ASTRA and EUTELSAT II-F1 satellites).
Connect the LNBs respectively to connectors 

d

and 

e

(IF INPUT A/B). In addition, your

receiver can supply ToneBurst (DiSEqC) control signals. This function allows connecting 4

LNBs to your receiver. The LNBs must be connected in 2s to each of the IF INPUTs 

d

and

e

, through a ToneBurst switch.

Press the

key to display the current mode, e.g. LnA1.

Press the key again to select the further mode.

DISPLAY

LNB

ToneBurst SIGNAL

DISPLAY

LNB

ToneBurst SIGNAL

LnA1   

A1

A Position

Lnb1   

B1

A Position

LnA2   

A2

B Position

Lnb2   

B2

B Position

2. Polarisation Selection
To allow transmission of the greatest possible number of programmes, satellite broadcasts
come in two polarisations (vertical and horizontal).
Press the

key to display the current polarisation, e.g. : "  V". 

Press the key again to select the other polarisation. 

Display : "  V" = vertical (14 V) 

Display : "  H" = horizontal (18 V)

3. Video Frequency Adjustment
Press the

key to display the frequency in MHz, e.g. : «1406».

The value displayed on your receiver is not the frequency of the channel;  it corresponds
to the difference between the channel frequency and the local oscillator frequency of your
LNB.

You can enter the desired frequency directly (4 digits) via the 0-9 numeric keypad, or

change the displayed value in steps of 1 MHz using the VOL + and VOL - keys.

Values outside the 700-2150 MHz band are not accepted. 

VIDEO

V/H

LNB

PROGRAMMING A NEW CHANNEL

Summary of Contents for ASR08T

















Reviews: