background image

3

ENGLISH

Important safety and operating information.

This set was designed and manufactured in accordance with international safety

standards.  You must nonetheless observe certain rules to guarantee optimum results and

safety.

Read

this user manual before attempting to put the set into service.

Ensure

that all connections (including mains connection and connector cables between

sets) are made according to manufacturer recommendations.

Switch off

the set and disconnect the power supply plug if you wish to change the

connections.

Consult

your dealer if you have any doubts about the installation, operation, or safety

of your set.

Do not continue

to use your set if you think it is operating abnormally, or if it is

damaged in any way.  (Switch it off, unplug the mains lead, and consult your dealer.)

Never open

your set, because this could expose you to dangerous voltages.

Do not obstruct

the ventilation slots on the set, e.g. with curtains.  Overheating can

cause damage and reduce the working life of your set.

Do not expose

the set to splashing water or dust.

Above all

Do not allow anyone (children in particular) to insert any object in the holes, slots, or other
openings in the housing.  This could result in a fatal electric shock.

Warning

Do not use cleaning products containing ethyl alcohol.
The identification label is located under the set.

Summary of Contents for ASR08T

















Reviews: