GB
How to retrieve
a programmed code
Method C – Programming by means
of code retrieval
Method D - Automatic
code search
Should none of the codes work, you still have the
possibility of retrieving the appropriate code without
having to perform any input.
1. Switch on the set you want to control.
2. Hold down the
S
key until the key that corresponds
to the last mode you selected blinks and then
remains lit.
3. Press the key that corresponds to the type of
equipment you want to control:
TV
: television set,
VCR/DVD
: video recorder - DVD player.
4. Direct the remote control towards the set and try to
switch it off by pressing the key
B
.
5. If the set you want to control switches off, press
ok
to memorise the subcode.
6. Should the set not switch off, press key
B
as
many times as required (up to 200 times), until
the set switches off. Between two key presses,
leave enough time for the key corresponding to
the selected mode enough time to light up again
(about 1 second). Proceeding this way will enable
you to see whether the set responds or not.
7. Immediately upon the switching-off of the set to be
controlled, press
ok
to store the code.
Check of the programming
:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Try out other remote control keys to find out the range
of functions you can control. If you think that not all
of the keys are active, repeat the procedure of this
programming method to find out the code supporting a
wider range of features.
With this method, the remote control scrolls through
the full code list by sending an IR signal to the set to be
controlled remotely. Proceed as follows:
1. Check that your equipment is on. If not, switch it
on manually.
2. Hold down the
S
key until the key that corresponds
to the last mode you selected blinks and then
remains lit (the indicator light remains on for a few
seconds to give you the time to proceed with the
following steps. The indicator lamp flashes to signal
that this time is almost up, and then goes off).
3. Release the
S
key.
4. Press the key corresponding to the type of
equipment (for example
TV
).
5. Press the
PRoG
p
or standby
B
or
PLAY
(
VCR
only) key. After a few seconds, the remote
control begins to scroll through the whole code
list included in the library (at a rate of roughly 1
code per second). Press the
PRoG
p
key once
again to slow down the test speed (1 code every
3 seconds). As soon as the set changes channels,
you must press
ok
to save the code and stop the
remote control scrolling through the list. If you do
not react quickly enough, you can go back to the
previous code by pressing
PRoG
q
or
REW
(
VCR
only) as many times as necessary (you can
go forward by pressing
B
,
PRoG
p
or
PLAY
(
VCR
only) if you have gone back too far). As
soon as the set responds again, press
ok
to save
the code.
It may be useful to retrieve the code programmed in
the remote control.
1. Hold down the
S
key until the key that corresponds
to the last mode you selected blinks and then
remains lit.
2. Press the key that corresponds to the type of
equipment you want to control:
TV
: television set,
VCR/DVD
: video recorder - DVD player.
3. Press the
S
key briefly, so that the last mode
selected blinks once.
4. Press the numbered keys in ascending order (
0
to
9
) until the selected mode blinks once.
5. The number that caused the selected mode to
blink is the first of the four numbers that make up
your code. Make a note of it below.
6. Repeat step 4 to find out the other numbers of the
code.
7. When the fourth number has been found, the
indicator light for the selected mode goes out.
6. Should the set not switch off, repeat step 2. Then
type in the next 4-digit code. Try to switch off the
set by pressing key
B
once. Repeat this procedure
by trying out each of the 4-digit codes.
Check of the programming
:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Check of
the programming
- For a television set: turn on the set and press, for
example,
to change channels.
- Video recorder: load a tape and then press
PLAY
(
B
).
- DVD player: load a DVD and then press
PLAY
(
B
).
Try other remote control keys to find out the range of
functions you can control. If you think that not all of
the keys are active, try the programming
Method
B
or
C
.
When you have retrieved the code of your
set, jot it down so that you can use it
whenever needed.
After battery replacement, you’ll have to
programme the remote control again.
oR
Method E – Programming for control of
a CoMBo (combined TV-VCR,TV/DVD,
VCR/DVD, … set)
Depending on the COMBO group (TV/VCR, VCR/
DVD, etc.) and the make, you will be required to enter
a single code for both devices in the COMBO, or to
enter two codes, one code per device. Consult the
separate list to discover this.
Before you start programming, you must find the
subcode or code of the subset to be controlled
(television or video recorder). Refer to the list supplied
with this user manual (see page subcodes or codes).
1. Switch on the COMBO you want to control.
2. Hold the
S
key down until the key corresponding to
the last selected mode blinks and then remains lit.
3. Press the key of the first device to control, and then
follow one of the programming methods A, B, C or
D previously described.
4. If a second code programming is required, then
repeat steps 2 and 3 above.
TV CoDE
VCR CoDE
DVD CoDE
01_GB_Roc2406B.indd 2
20/12/06 10:15:27
