THOMSON ROC2309 Operating Instructions Manual Download

Page: 3 / 26

recorder,

SAT

: satellite receiver, cable, DVBT, ADSL

and

AMP

: audio equipment.

4. While the indicator is lit, enter the fi rst digit of the

4-digit code proposed for the set to be controlled
(example: 0036 for Thomson).

5. Direct the remote control towards the set and try to

switch it off by pressing the key

6. Should the set not switch off, repeat step 2. Then

type in the next 4-digit code. Try to switch off the set
by pressing key

once. Repeat this procedure by

trying out each of the 4-digit codes.

Check of the programming:

In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page

Method C – Programming by means

of code retrieval

Should none of the codes work, you still have the
possibility of retrieving the appropriate code without
having to perform any input.

1. Switch on the set you want to control.
2. Hold down the

SETUP

key until the red indicator

light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp fl ashes to signal that this time is almost up,
and then goes off). Release the

SETUP

key.

3. Press the key that corresponds to the type of

equipment you want to control:

: television set,

DVD

: DVD player, Video

recorder,

SAT

: satellite receiver, cable, DVBT,

ADSL

4. Direct the remote control towards the set and try to

switch it off by pressing the key

5. If the set you want to control switches off, press

to memorise the code.

6. Should the set not switch off, press key

as many

times as required (up to 200 times), until the set
switches off. Between pressing the keys, be sure
to leave enough time for the indicator light to go
out and then relight (about 1 second). Proceeding
this way will enable you to see whether the set
responds or not.

7. Immediately upon the switching-off of the set to be

controlled, press

to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page

Try out other remote control keys to fi nd out the range
of functions you can control. If you think that not all
of the keys are active, repeat the procedure of this
programming method to fi nd out the code supporting a
wider range of features.

Method D – Automatic

code search

With this method, the remote control scrolls through
the full code list by sending an IR signal to the set to be
controlled remotely. Proceed as follows:

1. Switch on the set you want to control.
2. Hold down the

SETUP

key until the red indicator

3. Release the

SETUP

key.

4. Press the key that corresponds to the type of

equipment you want to control:

: television set,

DVD

: DVD player, Video

recorder,

SAT

: satellite receiver, cable, DVBT,

ADSL

5. Press the

P+

or standby

(DVD/VCR only)

key. After a few seconds, the remote control begins
to scroll through the whole code list included in the
library (at a rate of roughly 1 code per second).
Press the

P+

key once again to slow

down the test speed (1 code every 3 seconds). As
soon as the set changes channels (or turn off, or
start to play the disk), you must press

to save

the code and stop the remote control scrolling
through the list. If you do not react quickly enough,
you can go back to the previous code by pressing

P-

(DVD/VCR only) as many times as

necessary (you can go forward by pressing

P+

(DVD/VCR only) if you have gone back

too far). As soon as the set responds again, press

to save the code.

Method E – Programming for control of a

COMBO (combined TV-VCR, TV/DVD, VCR/

DVD, … set)

Depending on the COMBO group (TV/VCR, VCR/
DVD, etc.) and the make, you will be required to
enter a single code for both devices in the COMBO,
or to enter two codes, one code per device. Consult
the separate list to discover this. Before you start
programming, you must fi nd the subcode or code
of the subset to be controlled (television or video
recorder...). Refer to the list supplied with this user
manual (see page subcodes or codes).

1. Switch on the COMBO you want to control.
2. Hold the

SETUP

key down until the red indicator

lamp blinks and then remains lit. Release the

SETUP

key.

3. Press the key of the fi rst device to control, and then

follow one of the programming methods A, B, C or
D previously described.

4. If a second code programming is required, then

repeat steps 2 and 3 above.

How to retrieve

a programmed code

It may be useful to retrieve the code programmed in
the remote control.

1. Hold down the

SETUP

key until the red indicator

light blinks and then remains lit. Release the SETUP
key.

2. Press the key that corresponds to the type of

equipment you want to control:

: television set,

DVD

: DVD player, Video

recorder,

SAT

: satellite receiver, cable, DVBT,

ADSL.

3. Press the

SETUP

key again briefl y, the indicator

light blinks once.

4. Press the number keys (

) until you notice that

the indicator lamp blinks once.

5. The number which made the indicator lamp blink

is the fi rst of the four fi gures comprising your code,
write it down.

6. Repeat step 3 to fi nd out the 3 other numbers of

the code.

7. When the fourth fi gure is found, the indicator lamp

goes out.

Check of

the programming

- For a television or a satellite receiver: switch on

and, for example, press 2 to change channels,
etc...

- Video recorder: load a tape and then press

- DVD player: load a DVD and then press

Try other remote control keys to fi nd out the range of
functions you can control. If you think that not all of the
keys are active, try the programming

Method B

When you have retrieved the code of
your set, jot it down so that you can use it
whenever needed.
After battery replacement, you may have to
programme the remote control again.

Other functions

Placing all devices on standby

Press the

key twice in less than one second, keeping

it held down the second time. All the devices go on
standby one after the other (the devices which were
already on Standby may turn on).

Adjustment of ALL volume controls under a
specifi c mode

In its delivered state, the

ROC6309

is programmed

such that all modes will use their own Volume and
Mute functions if present.
You can allocate the volume control to one of the
modes of the remote control on condition that the
volume control exists on the corresponding device
(e.g. control of TV sound in TV mode, DVD mode, VCR
Mode, etc.).

1. Hold the

SETUP

key down until the red indicator

lamp blinks and then remains lit.

2. Release the

SETUP

key

3. Press the

key until the red indicator lamp blinks

once.

4. Press once on the mode key (

DVD

, …)

corresponding to the device whose volume will
always be controlled by the

VOL

and

keys.

5. Press the

key once. The red indicator lamp goes

off.

6. All other mode will now punch-through to your

chosen mode for Volume and Mute control.

Adjustment of the volume controls for EACH
mode.

You can decide that the volume control is functional
for each mode selected on condition that the volume
control exists on the corresponding device (e.g. control
of the television set sound in TV mode, the control of
the sound of the SAT receiver in SAT mode, …).

1. Hold the

SETUP

key down until the red indicator

lamp blinks and then remains lit.

2. Release the

SETUP

key

3. Press the

key until the red indicator lamp blinks

once.

4. Press once on the mode key (

DVD

, …)

corresponding to the device whose volume will
always be controlled by the

VOL

and

keys.

5. Press the

VOL-

key once.

6. Press the

key once. The red indicator lamp goes

off.

7. The chosen mode key will now use its own Volume

and Mute functions

Restoring the universal Volume/Mute
functions

If you have changed the universal volume and mute
functions, as described in the previous two sections,
you can reset the functions back to the factory settings:

1. Hold the

SETUP

key down until the red indicator

lamp blinks and then remains lit.

2. Release the

SETUP

key

3. Press the

key until the red indicator lamp blinks

once.

4. Press and release the

key. The red indicator

lamp will go off completely. The volume and mute
functions are now restored to their factory defaults.

TV CODE

DVD/SAT CODE

Replacing the batteries

Use 2 AAA 1.5 Volt batteries
1. Open the cover on the back of the remote control.
2. Check the +/– polarity on the batteries and inside

the compartment.

3. Insert the batteries.
4. Press the battery cover back into place.
When exchanging the batteries, it may be necessary to
reprogram the unit. Hence it is advisable to record the
codes needed for your devices.

00131872bda.indd Abs1:2-Abs1:3

05.10.2009 9:33:25 Uhr