52
Controls and Operations
AUTOMATIC
HYDRAULIC
POWER LEVELERS
FAILURE TO ACT IN ACCORDANCE WITH THE FOLLOWING
MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Read the entire operators manual and all precautions
prior to operating this equipment.
Do not use the jacks to change the tires. The system is designed as a leveling and
stabilizing system and is not meant to lift the motorhome off the ground.
Do not operate any system functions while anyone is under the motorhome.
Make sure that people and pets are clear of the coach when operating the leveling
system.
Do not attempt to operate the system while the motorhome is in motion.
Never place hands or other parts of the body near hydraulic leaks. Oil may penetrate
skin causing severe injury. Wear safety glasses when inspecting or servicing the
system to protect eyes from dirt, metal chips, or leaks, etc. Follow all other applicable
shop safety practices.
The motorhome should be parked on a fairly level surface. Ensure that there are
no obstructions in the extend or retract paths of the jacks. If the surface is soft due
to saturation or heat, place boards under the jacks to distribute the weight over a
larger area. Using a board which measures approximately 2' wide by 2' in length is
recommended. Ensure the front tires are pointing forward and not to the left or right.
Note:
Refer to manufacturer’s operations manual before operating.
The automatic hydraulic power leveling system allows quick and easy leveling of the
motorhome from the driver’s seat by utilizing the system touch panel. The following
instructions are general operating instructions.
Automatic Leveling
And Retraction
Procedure
CAUTION
MAKE SURE THERE ARE NO OBSTRUCTIONS IN
THE EXTEND OR RETRACT PATHS OF THE JACKS.
KEEP ALL PEOPLE CLEAR OF THE VEHICLE WHILE
OPERATING THE LEVELING SYSTEM.
Do not allow excessive motion in the motorhome during the Auto-Level operation.
This could cause the system to level improperly.
1.
TURN ON POWER
. The power to the unit must be turned on. You need to have
the engine running and the parking brake must be set to turn the control panel on.
Push the POWER touch pad to engage power. The power touch pad should be lit
when power is on.
2.
PRESS THE AUTO-LEVEL TOUCH PAD.
The system will automatically level
your vehicle. The control panel will send out a series of beeps to let you know that
AUTO-LEVEL is operating. When completed, the panel will signal a successful
Auto Level. After ten minutes, the panel will enter sleep mode.
3.
RETRACTING THE JACKS.
Your Lippert System provides you with the ability
to retract the jacks using the Retract All Jacks Button feature. Press and retract the
Retract All Jacks Button. All jacks will automatically retract. The jacks are retracted
when the Jacks Down light has gone out. Depending on the vehicle, full retraction
may take up to 90 seconds.
Note:
Zero point, or level position has been preset at the factory.
However, if you want to change the setting refer to the automatic
hydraulic levelers owner's manual for detailed information regarding
the proper procedures to do this.
Summary of Contents for Palazzo 2015
