background image

Page 22

23108-D02

DDSM100 Direct Drive Translation Stage

Chapter 8 Thorlabs Worldwide Contacts

Thorlabs verifies our compliance with the WEEE (Waste Electrical and Electronic

Equipment) directive of the European Community and the corresponding national

laws. Accordingly, all end users in the EC may return "end of life" Annex I category

electrical and electronic equipment sold after August 13, 2005 to Thorlabs, without

incurring disposal charges. Eligible units are marked with the crossed out "wheelie

bin" logo (see right), were sold to and are currently owned by a company or institute

within the EC, and are not dissembled or contaminated. Contact Thorlabs for more

information. Waste treatment is your own responsibility. "End of life" units must be

returned to Thorlabs or handed to a company specializing in waste recovery. Do not

dispose of the unit in a litter bin or at a public waste disposal site.

For technical support or sales inquiries, please visit us at 

www.thorlabs.com/contact

 for our most up-to-date contact information.  

USA, Canada, and South America 

Thorlabs, Inc.  

sales@thorlabs.com  

techsupport@thorlabs.com  

Europe 

 

Thorlabs GmbH  

europe@thorlabs.com 

France 

 

Thorlabs SAS  

sales.fr@thorlabs.com 

Japan 

 

Thorlabs Japan, Inc. 

sales@thorlabs.jp  

UK and Ireland 

 

Thorlabs Ltd.   

sales.uk@thorlabs.com  

techsupport.uk@thorlabs.com 

Scandinavia 

 

Thorlabs Sweden AB  

scandinavia@thorlabs.com 

Brazil 

 

Thorlabs Vendas de Fotônicos Ltda. 

brasil@thorlabs.com  

China 

 

Thorlabs China  

chinasales@thorlabs.com 

Summary of Contents for DDSM100


























Reviews: