background image

QS15 & QS20 Series Galvo Scanners

 

Chapter 10: Regulatory

 

Rev A, June 20, 2022 

Page 11

 

Chapter 10 

Regulatory 

As required by the WEEE (Waste Electrical and Electronic Equipment Directive) of the European Community and 
the corresponding national laws, Thorlabs offers all end users in the EC the possibility to return “end of life” units 
without incurring disposal charges. 

 

This offer is valid for Thorlabs electrical and electronic equipment: 

 

Sold after August 13, 2005  

 

M

arked correspondingly with the crossed out “wheelie bin” logo (see right) 

 

Sold to a company or institute within the EC  

 

Currently owned by a company or institute within the EC  

 

Still complete, not disassembled and not contaminated 

As the WEEE directive applies to self-contained operational electrical and electronic products, this end of life take 
back service does not refer to other Thorlabs products, such as: 

 

Pure OEM products, that means assemblies to be built into a unit by the user (e. g. OEM laser driver cards)  

 

Components  

 

Mechanics and optics  

 

L

eft over parts of units disassembled by the user (PCB’s, housings etc.).  

If you wish to return a Thorlabs unit for waste recovery, please contact Thorlabs or your nearest dealer for further 
information. 

Waste Treatment is Your Own Responsibility 

If you do not return an “end of life” unit to Thorlabs, you must hand it to a company specialized in waste recovery. 
Do not dispose of the unit in a litter bin or at a public waste disposal site. 

Ecological Background 

It is well known that WEEE pollutes the environment by releasing toxic products during decomposition. The aim of 
the European RoHS directive is to reduce the content of toxic substances in electronic products in the future. 

The intent of the WEEE directive is to enforce the recycling of WEEE. A controlled recycling of end of life products 
will thereby avoid negative impacts on the environment. 

Summary of Contents for QS15 Series
















Reviews: