background image

© 2017 Thorlabs GmbH

1 General Information

3

1   General Information

The TXP5016 16 channel Test an Measurement Platform chassis is designed to accommodate
up  to  16  TXP  modules.  These  modules  are  controlled  by  an  external  PC,  connected  via  the
Ethernet  interface  of  the  TXP5016.  It  has  a  wide  range  power  supply  compatible  with  line
voltages between 100...240VAC, 50-60Hz.

·

Small footprint with 16 module slots

·

Hosts any TXP Series module

·

Intelligent modules - memory / processor capacity where needed (real time apps)

·

Configurable module pooling for complex measurement solutions

·

Programming Interface
USB interface with LabVIEW

®

 / LabWindows/CVI

® 

and C drivers

Enhanced macro function capabilities 

·

Remote control via Ethernet connection

·

Mainframe configuration via RS232 or TCP/IP connection

1.1   Safety

 Attention 

All statements regarding safety of operation and technical data in this instruction manual
will only apply when the unit is operated correctly as it was designed for.

Prior to applying power to the TXP5016, make sure that the protective conductor of the 3
conductor  mains  power  cord  is  correctly  connected  to  the  protective  earth  ground
contact of the socket outlet! Improper grounding can cause electric shock with damages
to your health or even death!

All modules must only be operated with proper shielded connection cables.

The TXP5016 must not be operated in explosion endangered environments!

Do not remove covers! Do not obstruct the air ventilation slots in the housing!

Do not open the cabinet, there are no parts serviceable by the operator inside!

Refer servicing to qualified personnel!

Only  with  written  consent  from 

Thorlabs  GmbH

  may  changes  to  single  components  be

made or components not supplied by 

Thorlabs GmbH

 be used. 

This  precision  device  is  only  serviceable  if  properly  packed  into  the  complete  original
packaging. If necessary, ask for a replacement package prior to return.

 Attention 

The  following  statement  applies  to  the  products  covered  in  this  manual,  unless
otherwise  specified  herein.  The  statement  for  other  products  will  appear  in  the
accompanying documentation.

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules and meets all requirements of the Canadian
Interference-Causing  Equipment  Standard  ICES-003  for  digital  apparatus.  These  limits
are  designed  to  provide  reasonable  protection  against  harmful  interference  when  the
equipment  is  operated  in  a  commercial  environment.  This  equipment  generates,  uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the  instruction  manual,  may  cause  harmful  interference  to  radio  communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

Summary of Contents for TXP5016













































Reviews: