-20-
Tail Unit /
尾部總成組裝
Bag I+J
No.
1
2
3
4
5
6
7
Qty
Material No. Description
名稱
No.
8
9
10
11
12
13
Qty
Material No. Description
名稱
BK2253
HMC3-14B
HSA3-6
BK2563
BK2564
BK0524-T
BK0447
HMJ2-8N
HMC3-16B
HMM3Z
BK2553
HMC3-10B
HNJ-1
六角支柱
內六角螺絲, M3x14
半圓頭內六角螺絲, M3x6
金屬固定座(上)
金屬固定座(下)
尾管支撐架
尾管支撐架接頭
自攻螺絲(細), M2x8
內六角螺絲, M3x16
止鬆螺帽, M3
支撐架
內六角螺絲, M3x10
束帶(小)
FRAME SPACER
SOCKET SCREW , M3x14
BUTTON HEAD SOCKET SCREW, M3X6
METAL TAIL SUPPORT BRACKET(UPPER)
METAL TAIL SUPPORT BRACKET(LOWER)
TAIL SUPPORT ROD
TAIL SUPPORT ROD END
SELF TAPPING SCREW, M2x8
SOCKET SCREW, M3x16
NYLON NUT, M3
SUPPORT BRACKET
SOCKET SCREW, M3x10
NYLON STRAP,100mm
1
2
2
1
1
2
4
4
2
3
2
1
4
HSA3-6
BUTTON HEAD SOCKET SCREW, M3X6
半圓頭內六角螺絲, M3x6
HMC3-14B
SOCKET SCREW,M3x14
內六角螺絲,M3x14
HMM3Z
NYLON NUT,M3
止鬆螺帽,M3
HMC3-16B
SOCKET SCREW,M3x16
內六角螺絲,M3x16
HMC3-10B
SOCKET SCREW,M3x10
內六角螺絲,M3x10
HMJ2-8N
SELF TAPPING SCREW-M2x8
自攻螺絲(細)-M2x8
This hole (Left & Right side
both) is design for 140°Control
Arms(PV1409)
此孔位（左右二側）用於140°控
制搖臂（PV1409）
(3)
(3)
(1)
(10)
(10)
(11)
(11)
(12)
(13)
(13)
(5)
(6)
(8)
(8)
(7)
(7)
(7)
(2)
(1)
(2)
(7)
(2)
(2)
(4)
(9)
Ensure the setting screws (#3) line up to the retaining hole.
鎖固時，請確認鎖固螺絲#3正確對正定位孔。
Secure the screws into the Frame
Spacer when attaching the Tail
Support Rod End on the Main Frames.
安裝尾管支撐桿於側板上時，請注意需將
鎖固螺絲鎖固於六角固定支柱上。
Rear View 後視圖
Must be purchased separately
改裝品需另購
Stick some cycles of thin tape properly onto
the position where the Brackets clip to prevent
any indentation on the tail boom caused by
over tighten or vibration.
纏繞適當圈數薄膠帶於尾管固定座夾持位置上，可
避免因夾持過緊或機體震動而造成尾管上壓痕。
Apply threadlocker
使用螺絲防鬆膠
All manuals and user guides at all-guides.com
all-guides.com
