background image

JK6053

This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.  

It does not cover any damage caused by use or modification.  The warranty does not extend 

beyond the product itself and is limited only to the original cost of the kit.  By the act of building this 

user-assembled kit, the user accepts all resulting in liability for damage caused by the final 

product.  If the buyer is not prepared to accept this liability, it can be returned new and unused to 

the place of purchase for a refund.

Warranty

Notice:  Adult  Supervision Required

This is not a toy.  Assembly and flying of this product requires adult supervision. 

Read through this book completely and become familiar with the assembly and flight of this A119.  

Inspect all parts for completeness and damage.  Browse www.thundertiger.com for customer 

service if you encounter any problems.

No.3843  

MEMO

16

Assembly Manual

Specifications:

Fuselage Length (less rotor): 57-1/4”(1450mm)
Fuselage Width (less rotor): 13”(330mm)
Fuselage Height: 18-1/4”(465mm) 
Full-Equipped Weight: 8.38 lbs (3800g)

1

Summary of Contents for Agusta A 119 Koala









Reviews: