PARTS CHECK LIST
ASSEMBLY
Kit Contents
1. Locate the molded marks for landing strut, screw
holes and engine cooling openings at the bottom of
the fuselage. Note these marks are only for reference
of Raptors, shall you install it on other branded
helicopters then you will have to find out the correct
opening position for landing strut before you drill or
trim the fuselage.
7
6
Enlarge the strut hole for about 2~3mm wider as the
Silicon Fairing will be installed in the hole. Do not
glue the Silicon Fairing at this step. It is very
important to make sure that silicon fairing is loosened
in the hole instead of tight.
2. Put the scale fuselage aside for a moment and get
your heli prepared. For Raptor owners, please remove
the Landing Skid,Tail Fins, Boom Supports and Tail
Rotor Assembly. Locate the Extended Rear Frames,
which are specially designed for this MD fuselage.
Secure the Extended Rear Frame in place with the
screws and washers. (3x18mm self tapping screw for
the top; 3x10mm washer self-tapping screw and big
flat washer for the bottom).
3. Assemble the Landing Skid as shown. Temporarily
install the Brace under the side frame. Adjust the
Landing Skid as shown and make sure it sits on the
table firmly. Secure the Joiner & Skid Pipe with the
furnished 3x3mm Set Screw. Do not over-tighten the
setscrews; just make sure the skid pipe will not rotate.
Then secure the Joiner and the Aluminum Strut with
2.6x10mm Self-Tapping Screw. Next press the end
cap on skid pipe.
4. Remove the landing skid assembly from Heli.
Remove the brace from the aluminum strut. Do not
remove the strut and skid pipe as they are already
adjusted and secured. Place the brace in place and
install the strut and skid pipe onto the brace. You may
apply Vaseline on Silicon Fairing to increase the
lubrication for easier installation.
Fuselage
Fuselage(1)
Plastic Tube(1)
Tail Boom Foam Retainer(1)
Silicon Grommet(3)
Exhaust(1)
Silicon Strut Fairing(4)
Windshield
Left Front Window(1)
Right Front Window(1)
Left Rear Window(1)
Right Rear Window(1)
Front Windshield(1)
Tai l
Horizontal Tail(1)
Left Tip Fin(1)
Right Tip Fin(1)
Tail Skid(1)
Vertical Fin(1)
Body Retainer
Wire Strike(2)
Handlebar(4)
Post(3)
Landing Skid
Brace(2)
Al.Strut(F/2)
Al.Strut(R/2)
Skid Joiner(L/2)
Skid Joiner(R/2)
Step Bar(4)
Skid Pipe(2)
Skid Pipe End Cap(4)
Step Bar End Cap(4)
Rear Frame
Rear Frame(L/1)
Rear Frame(R/1)
Washer(2)
Screw
M2 Nut(16)
M3 Washer(4)
M3 Locknut(6)
2X5mm Screw(16)
2X5mm Wood Screw(40)
2X8mm Wood Screw(4)
3X18mm Wood Screw(3)
3X3mm Set Screw(4)
2.6X10mm Self-Tapping Screw(4)
3X18mm Self-Tapping Screw (4)
2.6X14mm Socket Screw(8)
3X20mm Socket Screw(4)
3X23mm Socket Screw(2)
3X25mm Socket Screw(2)
3X40mm Socket Screw(2)
3X10mm Washer Self-Tapping Screw(3,B)
3X10mm Washer Self-Tapping Screw(2,S)
