INSTRUCTION MANUAL
TDBT01
Charging the Battery
Before using this product, fully charge the
TDBT01
headset by
plugging the provided charging cable into the Charging Port
on the headset, and a USB power source (not included).
The LED Indicator will turn BLUE when the battery is fully charged.
Headset Functions
1. Power ON your headset:
2. Power OFF your headset:
Pairing the TDBT01 Headset to Your Phone:
1
. Turn your phone
OFF
entirely and then turn it back
ON
to refresh its Bluetooth memory.
2
. Find the Bluetooth menu on your mobile phone turn the Bluetooth function
ON
(Check your mobile phone user guide)
4
. On your phone, perform a Bluetooth “device discovery” to add the
TDBT01
headset as a new device. It only takes a few seconds to search
& find the
TDBT01
Bluetooth headset.
5
. When the
TDBT01
headset is discovered (found) the phone will display “
TDBT01
” in the menu. Choose/Tap on “
TDBT01
”.
6
. If prompted by your phone to enter a code, enter; "
0000
" and the phone will now pair with the headset and be ready to use.
7
. If supported by your phone menu, set the
TDBT01
as "set as authorized "or "add to trusted devices".
8
. Keep the Bluetooth function on your phone
ON
with your phone near, and the headset will automatically pair.
9
. If the pairing is not successful, the headset will shortly return to the standby mode. Please repeat the process to try pairing again.
10.
Refer to your phones User Manual for any additional steps or special features for your phone.
Note
: To conserve power, the unit automatically turns off when not paired with your Bluetooth Phone.
For Assistance please call 1-855-994-8364. Do NOT return this product to your retailer.
Operating the Headset:
1.
To
ANSWER or END a call:
2.
To REJECT* a call:
3.
To REDIAL* the last call:
Press the Multifunction button twice while the headset is in “Standby mode” (not currently on a call or listening to music).
4. T
o adjust the VOLUME:
5.
To PLAY/PAUSE music:
3
. With the
TDBT01
OFF, hold the headset 12” inches away from your mobile phone and turn the Power ON as described above.
Press and Hold the Multifunction button for about 8 seconds until the LED indicator flashes blue and red alternating which indicates
your headset is in PAIRING MODE and is now ready to be “paired” with your Bluetooth Mobile Phone.
Press the Multifunction button once when there is an incoming call to answer. Press the Multifunction button once again to end the call.
Press and Hold the the Multifunction button (approx. 2 seconds) when there is an incoming call you want to ignore/send to voicemail.
* To use these functions, your phone/device must also support the Bluetooth Profile.
Press and Hold the Multifunction button for about 5 seconds.
Press and Hold the Multifunction button for about 5 seconds.
You will hear a short beep, and the LED will flash RED.
You will hear a short beep, and the LED will flash BLUE.
11.
To pair a second device, turn the first phone’s Bluetooth function, and the headset,
OFF
and repeat steps 3-10 using the second device.
6.
To change the SONG / TRACK:
The Volume can be adjusted up/down by using the controls/buttons on your phone/device.
While listening to music, press the Multifunction button once to Pause playback. Press the Multifunction button once again to resume.
To change the song/track use the controls/buttons on your phone/device.
Disconnecting the Headset:
To Disconnect or Unpair your phone from the headset go to the Bluetooth menu on your phone/device and choose Disconnect under TDBT01.
Refer to your phone/device’s instruction manual for instructions on finding the Bluetooth Menu and any additional steps for disconnection.
