background image

3. INSTALLATION

3.4 Virtual wire installation

The virtual wire can be installed in one of the following

-  Securing the wire to the ground with pegs. 

   It is preferable to staple down the virtual wire, if you

  

adjustments to the virtual wire during 

 want to make 

-  Bury the wire

   It is preferable to bury the virtual wire(max depth: 5cm)

   

the lawn.

 if you want to detach or aerate 

   If necessary both methods can be combined so one 

   

wire is stapled down and the

part of the virtual 

- Install virtual wire with pegs 1 meter apart. It’s 

  

best to use smooth radius corners than sharp 

- Bury virtual wire below grass and fasten it on 

  

that the mower should

the ground with pegs, so 

 

 not cut the wire. 

virtual wire

Add pegs in order to pull the
virtual wire down to the ground 
surface, below the grass tips.

OK

IMPORTANT

  

INFORMATION

Hard or dry ground may cause pegs to break when

 driving them in. In extreme cases, watering the lawn

ways:

   the first few weeks of operation.

   remainder is buried.

 where the pegs will be driven.

- A minimum distances between the front of the charging

  station and an 

And make sure the 

obstacle is 2 meters. 

 

 least 

distance from corner to front of charging station is at

 2.5 meters. Make sure to lay a 2.5 meters minimum 

- If a high obstacle, for example a house, wall, fence or 

   other obstacle which is higher than the cutting lawn  

  

prevent mower 

 at least 40cm from the obstacle. This will 

120

10cm

Pool

Max:1cm

Pa ssage or  
a ground wi th 
same level 
of the lawn .

Min:40cm

Min:40CM

Straight-line
at least:2.5m

15cm

House

wall, fence or

 

other

 

obstacle

 

higher 

than the lawn

Location 1.

Location 2.

15cm

  

virtual wire in front of charging station.

straight-light of 

   

the virtual wire should be laid 

borders the working area, 

   

with the obstacle.

from colliding 

 

- If a passage or a ground with same height of cutting lawn, 
the virtual wire should be laid at least 10cm from the edge. 

- A minimum distance between the pool edge of virtual 

wire is 40cm.

- A maximum distance of the virtual wire
to and from the island is 1cm, and fix the  

- There are two types of set up of the 

virtual wire around the charging station. 

1. Put the charging station near corner. 

please take location 1 for reference. 

2. Put the charging station in middle of 
wire, please take location 2 for reference. 

Please make sure to set a straight-line  
at least of 2.5m in front of charging 
station. The charging station should be 
far away from puddle. 

- 7 -

two wires with one peg.  

  

. See pictures.

angles

- A minimum distance between two corners is 1meter. 

Summary of Contents for ROBOT MOWER






















Reviews: