2
3
4
©
2017 TiCad GmbH & Co. KG – All rights reserved.
YOUR TICAD ANDANTE IN DETAIL
1 Delta leather handle
2 Umbrella adapter
3 Drawbar
4 Top firm-fix connection
5 Top bag holder
6 Fastening straps
7 Centre bar
8 Bottom firm-fix connection
9 Shaft
10 Locking pin
11 Locking brake
12 Knurled sleeve
13 Wheel made of GRP*
14 Bottom bar
15 Bottom bag holder
16 Front shaft
17 Front wheel made of GRP*
Image:
TiCad Andante
with GRP* wheels, also available as
TiCad Andante
Classic with titanium wheels
SETTING UP YOUR TROLLEY
Fitting the shaft:
Before fitting the shaft, pull back the locking pin (black round
handle) and turn it slightly to the right (about 45°). Next, in-
sert the shaft halfway into the frame with the brake mounted on
the left and release the locking pin by turning the black handle
back again. You can now insert the shaft fully into the frame
until it engages. To lock the shaft into place for the integrated
locking brake, continue turning it until it engages again.
Removing and attaching the wheels
READ ME FIRST
TiCad
ANDANTE
*Glass-fibre reinforced plastic (PA 6 GF 30)
Congratulations!
You have chosen an excellent product manufactured by TiCad! All
of our high-quality products are carefully handmade at our pro-
duction facility in Altenstadt (Hessen, Germany).
To ensure that you will be able to enjoy your trolley for a very
long time, please take some time to carefully read through these
operating instructions, which contain important information that
will make using your trolley a lot easier.
If you have any further questions regarding the use or care of your
trolley, please contact your specialist dealer.
We would like to wish you many enjoyable games
of golf and a lot of success! Your TiCad team
Shaft with locking pin groove and arrester
Locking pin
Frame connections (firm-fix connections):
The frame of your TiCad trolley is assembled with firm-fix con-
nections. To connect the frame sections, simply press them into
one another and slightly turn one of the sections to allow the cou-
pling system to engage (1+2). It will have engaged once the outer
ring has slid over the joint. To open the connection, pull the outer
ring back (3).
1
3
2
Engaging (1+2) and opening (3) the
firm-fix connections
Bag holder:
The top bag holder is fitted into place with an expansion bolt.
The expansion bolt must not be turned in too far (see images),
because there has to be a gap between the expansion bolt and
the start of the thread. To fit the bag holder, insert it into the frame
and then align and fix it into place by twisting the bag holder.
Expansion bolt turned in too far
Bag holder
Expansion bolt in the correct position
Attaching the golf bag:
Put your golf bag onto the trolley before attaching the drawbar.
To fasten the golf bag, insert one of the round fasteners into the
strap of the opposite fastening strap. When doing so, make sure
not to flick the fasteners, as this may cause injury. To undo the
fastening straps, hold on to the bottom strap and then pull out the
top fastening strap with your other hand.
We recommend fitting the drawbar only once the golf bag
has been attached to prevent the trolley from tipping over.
Umbrella adapter:
The umbrella adapter is located at the top end of the drawbar.
Screw the umbrella holder into the tapered adapter. The adapter
can only be used in the standard position on the drawbar.
Umbrella adapter with
TiCad umbrella holder
Locking brake:
The locking brake has to be fitted on the left wheel. To open and
apply the brake, simply move the locking lever back or forward.
Locking brake when opened
Locking brake when applied
Care:
The frame of your TiCad trolley is made of a high-quality, rust-
proof material and has been sealed to keep out rain. The frame
can be cleaned with a conventional household cleaning prod-
uct – but
not
with abrasive cleaners. The titanium‘s shine can
be restored with a special cleaning oil available from TiCad.
The hubs of the wheels and the couplings
must not
be oiled or
greased.
USING YOUR TROLLEY
Always handle your TiCad trolley slowly and carefully when
moving over rough ground that contains stones or pot-
holes. Avoid kerb edges.
1
2
3
4
5
6
6
7
9
9
13
13
15
16
17
12
12
12
14
11
10
8
1
2
3
4
Attaching the wheels:
The wheels can be attached and removed by pulling back the
knurled sleeve. When attaching the wheels, slightly turning the
sleeve can make it easier for the wheels to engage.
Always make sure that no dirt gets into the hub. The hubs
must not be oiled or greased.
