I N S T R U M E N T S & C O N T R O L S
7-23
ALARM MESSAGES -
CAUTION
MESSAGE
DESCRIPTION
No Cluster Data
The Graphical Instrument Cluster has an internal error – the graphics application
has reported it has not received data from the cluster application within the last
15 seconds.
No J1939-I Data
No messages have been received on the J1939 network within the last 15 seconds.
Check to confirm the J1939 connector is plugged into the Graphical Instrument
Cluster or if there is a problem with the J1939 network.
No Serial-I Data
The Graphical Instrument Cluster has an internal error – the I/O board has not
received a valid serial message from the cluster application within the last 15
seconds.
No J1939 C Data
Not receiving any J1939 messages from the Engine Controller
No Serial-C Data
The Graphical Instrument Cluster has an internal error – the cluster application has
not received a valid serial message from the I/O board within the last 15 seconds.
Low Fuel
The vehicle fuel tank is low – refer to the ‘Distance to empty” display
.
Regen in Process
Indicates that Active Regeneration is in progress (see below).
High Exhaust Temp.
Indicates that high exhaust temperatures may exist due to Active Regeneration
(soot burn-off) in the diesel particulate filter (DPF). This is normal and does not
signify the need for vehicle or engine service. Ensure the exhaust pipe outlet is not
directed at any combustible surface or material.
CAUTION
messages relate to items that require your attention.
Summary of Contents for PowerGlide 2019
