9
EN
ENGLISH
(Translation of the Original Instructions)
Do not touch engine components which
get hot during use . Burns hazard .
Disengage the cutting means or the
PTO, set the engine to the idle position,
stop the engine and remove the key
(make sure that all moving parts have
come to a complete stop):
a. whenever you leave the machine
unattended or leave the driver’r seat.
b. before removing the jamming cause
or unclogging the collector channel;
c. before checking, cleaning or working
on machine;
d. after striking a foreign object. Inspect
the machine for damage and make
repairs before restarting and opera-
ting the machine;
Disengage the cutting means or the
PTO and stop the engine (make sure
that all moving parts have come to a
complete stop):
a. Before refuelling;
b. Every time you remove the grass col-
lector sack or put it back on;
c. adjusting the cutting height, assuming
this operation cannot be done from
the driver’s seat.
Disengage the cutting means or the
PTO during transport or whenever the
machine is not being used .
Reduce the throttle setting before stop-
ping the engine. turn the fuel off at the
conclusion of mowing, following the in-
structions in the manual .
Take care with multiple cutting means
as one rotating cutting mean may cau-
se other cutting means to rotate .
WARNING - In the event of failures or
accidents when working with the ma-
chine, stop the engine immediately
and move the machine away to avoid
causing further damage; in the event of
accidents with injuries to operators or
third parties, take the first aid measures
which are most appropriate to deal with
the situation and contact a health care
facility for the necessary treatment . Ca-
refully remove any debris which could
cause damage or injury to persons or
animals if ignored .
CAUTION! The noise and vibration le-
vels shown in these instructions are
the maximum levels for use of the ma-
chine . The use of an unbalanced cutting
element, the excessive speed of move-
ment, or the absence of maintenance
have a significant influence on noise
emissions and vibrations . Consequen-
tly, it is necessary to take preventive
steps to eliminate possible damage
due to high levels of noise and stress
from vibration . Maintain the machine
well, wear ear protection devices, and
take breaks while working .
3 .4 MAINTENANCE AND STORAGE
CAUTION! - Before cleaning or doing
maintenance work, take out the ignition
key and read the relevant instructions .
Wear adequate clothing and work glo-
ves whenever your hands are at risk .
CAUTION! - Never use the machine with
worn or damaged parts . Faulty or worn-
out parts must always be replaced and
never repaired . Only use original spa-
re parts: The use or non-original and/
or incorrectly fitted parts will compro
-
mise the safety of the machine, may
cause accidents or personal injuries
for which the Manufacturer is under no
circumstance liable or responsible .
Any regulations and maintenance ope-
rations not described herein must be
carried out by your Dealer or Authorized
Service Centre, which have the necessa-
ry knowledge and equipment to ensure
that the work is carried out correctly,
maintaining the correct degree of safety
and the original operating conditions of
the machine . Any adjustments or main-
tenance operations carried out by peo-
ple not having the necessary knowledge
will nullify the warranty and exonerate
the manufacturer from all liability .
• After each use of the machine, remove the key
and check for any damage.
• Keep all nuts, bolts and screws tight to be sure
the equipment is in safe working condition.
Regular maintenance is essential for safety and
for maintaining performance levels.
• Regularly check that the cutting means screws
are securely tightened.
Summary of Contents for P 901 PH
