page 20
Run the jet pump to circulate the spa water for a ten-minute period (clean cycle). Repeat this procedure until all SmartJet lever operating
positions have been tested.
10. Recheck the Total Alkalinity (TA) at 80 ppm, Calcium Hardness (CH) at 100 ppm, then spa water pH at between 7.4 and 7.6.
OPERATIONAl NOTE:
Make sure you adjust your Total Alkalinity first, as an out-of-balance condition will affect your ability to adjust the pH
correctly, and will prevent the sanitizer from operating effectively. The spa is ready for use when the spa water has circulated through each
SmartJet
®
lever operating position and the chlorine level remains between 3 ppm and 5 ppm.
11. The spa temperature is pre-programmed to reach 100°F (38°C), and will normally do so within 18 to 24 hours. You may raise the water
temperature by pressing the TEMP (+) button on the control panel, or lower it by pressing TEMP (-) button. After a few hours, the water
temperature will remain within 1½ degrees of your selected temperature. To prevent tampering, you can lock your desired temperature setting.
Refer to the Control Panel section for details.
NOTE:
Allowing the jet pump to operate for long uninterrupted periods of time with the cover in place will cause a rise in the spa water
temperature. All spas are equipped with a safety device to reduce the risk of component damage or personal injury, should the jet pump be left
running continuously for a long period of time. After two hours of continuous operation, the jet pump controller will automatically turn off the jet
pump.
SMARTJET
®
SYSTEM
With your Tiger River
®
spa’s exclusive SmartJet system hydromassage design, you can control the massaging action of your spa. Using the
SmartJet
lever, the jets are activated in sets, known as jet systems.
The Sumatran
®
and Bengal
®
(MM) models have two jet systems that are activated by turning the SmartJet lever(s)
to the 3 or 9 o’clock position. On the Bengal (M) model, the SmartJet system lever controls four jet
systems. To access a jet system, simply turn the SmartJet system lever to the 3, 6, 9 or 12 o’clock
position (facing the spa) to access the four jet systems.
NOTE:
The SmartJet system is not used on the Caspian
™
.
Please consult the jet system menus on the following pages to determine which jets are
activated
with each SmartJet lever position. Or just jump in and play – turn the lever and see what happens.
COMFORT CONTROL
®
SYSTEM
The Comfort Control system allows you to control the intensity of the Precision
®
jets by adjusting
the mixture of air and water. Turn the Comfort Control lever clockwise to decrease the intensity of
the Precision
jets and counterclockwise to increase the intensity.
JETS
JeTSTReaM
®
JeTS
The JetStream jet is a large orifice hydromassage jet designed to put maximum massaging action on a specific area of
the body. It is located in the lower part of the spa to afford optimal access for the massaging of feet, legs, hips, and lower back.
pReCISIOn
®
JeTS
Precision jets are small, producing a precisely narrow stream of massaging action. They are placed in groups to perform a soft, soothing massage
on your back, neck, and shoulders, or in the FootWell
®
system of the Caspian and Bengal spas as foot massagers.
hydROMaSSage JeTS
The directional and rotary hydromassage jets are adjustable. The intensity of these jets is determined by the volume of air being induced into the
jet chambers and mixing with the water stream. You have direct control of the intensity of the jet by rotating the jet faceplate either clockwise to
decrease pressure, or counterclockwise to increase pressure.
The hydromassage jets have the option of two different nozzles (directional and dual port rotary). The directional nozzle allows you to aim the
water in the direction that feels best. The dual port rotary nozzle divides the water flow into two streams, and then spins. Again, the faceplates on
the rotary jets are used to change their intensity and speed of rotation. In addition to being adjustable, the rotary and directional jet nozzles are
interchangeable. Simply grip the rotary or directional jet nozzle and pull it out of the jet retainer. Position the replacement nozzle at the desired jet
location and push it into the retainer.
ACCESSORY NOTE:
Your Tiger River dealer stocks hydromassage jet kits which can easily be installed in your spa to modify your jets from
directional to dual port rotary.
Operating Instructions
3 o’clock
9 o’clock
6 o’clock
12 o’clock
Increase Air
Volume
Decrease Air
Volume
Summary of Contents for Bengal
Page 1: ......
