CONTROL PANEL MENU dISPLAY
The control panel consists of four main menus. These menus are; Set Temperature, System, Lite+ and Tools. The Lite+ menu will only appear if
the spa is equipped with an optional multicolor light (if equipped with the optional multicolor light, use the reference card provided with the light for
operating instructions).
Press the MODE ▲ or MODE ▼ button to scroll through the main menus. Once the desired menu is illustrated, press the ON ▲ button to activate
the menu.
TEMPERATURE CONTROL
The set temperature range is from 80°F to 104°F (27°C to 40°C). (The temperature of any setting may rise slightly depending on the current use
and condition of your spa, and on outside temperature.)
The set temperature of the spa water will automatically be 100°F (38°C) the first time power is applied. This is
the setting programmed at the factory. After the spa has been set up and used, the last temperature value set by
the user will be stored in memory. If power is disconnected from the spa, it will automatically revert to the last set
temperature when power is reapplied.
To display the set temperature of the spa, press the ON ▲ button. The set temperature will be displayed, unless
the spa is locked (in which case the lock icon is displayed). The set temperature display will automatically shut off after 30 seconds.
To increase the set temperature of the spa water, press ON ▲ button. Each time the button is pressed, the set temperature display will increment
by one degree. If the button is held down, the set temperature display will increase by one degree every half-second.
To decrease the set temperature of the spa water, press the OFF ▼ button . Each time the button is pressed, the set temperature display will
decrement by one degree. If the button is held down, the set temperature display will decrease by one degree every half-second.
If the set temperature value will not change, check the
TEMPERATURE LOCK
and
SPA LOCK
features. When either of these features is applied,
the temperature control is disabled. To activate the temperature control buttons, remove all locking features applied.
SYSTEM MOdE
Your Tiger River
®
spa is equipped with a System Mode. This function will allow you to conveniently turn the
jet(s) on high speed and the light on maximum intensity at the same time.
To activate the system mode, perform the following functions:
Press the MODE ▲ button until the SYSTM symbol is illuminated on the display. The jets and light icons will
flash until the system mode is activated. Press the ON ▲ button to activate the SYSTM mode feature.
NOTE:
Once activated, the jet and light functions can still be changed by pressing the JETS or LIGHT button.
To deactivate the system mode, press the MODE ▲ button until the SYSTM symbol is illuminated on the display. Press the OFF ▼ button to
deactivate.
TOOLS MENU
The TOOLS menu is one of the main menus on the control panel. Within the TOOLS menu are six submenus, which
consists of; Clean, Temp Lock, Spa Lock, Summer Timer and Exit.
To enter into the TOOLS
menu, scroll through the main menus using the MODE ▲ or MODE ▼ button until the
TOOLS
menu is illustrated. Press the ON ▲ button to enter into the
TOOLS
submenu, use the MODE ▲ or
MODE ▼ button to scroll through the submenus. Once the desired submenu is illustrated, press the ON ▲ button
to activate the submenu or press the OFF ▼ button to deactivate the submenu. To leave the TOOLS submenu,
scroll through the submenu until EXIT is illustrated, press the ON ▲ button to exit the submenu.
CLeanIng MOde
All Tiger River spas are equipped with a “Cleaning” mode. When the mode is activated, the jet pump in the first jet
system will turn on and run for ten minutes (used for water maintenance). To activate the “Cleaning" mode, press
the MODE ▲ or MODE ▼ button until the
TOOLS
menu is illustrated. Then press the ON ▲ button to enter the
TOOLS submenus. The CLEAN symbol will illuminated (the CLEAN mode is the first submenu) on the display.
Press the ON ▲ button to activate the CLEAN mode feature.
NOTE:
The jet icon will remain solid in the CLEAN display and will flash on and off in the main display while the
“Cleaning ” mode is active.
To stop the Cleaning Cycle before the ten minutes is complete, Press the MODE ▲ button until the TOOLS menu is illuminated then press the ON
button to enter the TOOLS submenus where the CLEAN symbol is illuminated on the display. Press the OFF ▼ button to deactivate.
NOTE:
Pressing the JETS button will also deactivate the clean cycle.
System Display Active
Clean Cycle Active
page 27
Control panel Operations
Set Temperature Display
Tools Display
Summary of Contents for Bengal
Page 1: ......
