background image

19

How to Clean

When the cleaning with 

citric acid is complete, 

all flavor and strength 

selection keys light, 

and the [Start|Stop] 

key turns off.

 

‘

Two short beeps 

will sound every 

3 seconds.

7

Off

On

Two short 

beeps

 Removing mineral components from the path inside the main unit (cleaning with citric acid; continued)

Remove the cylinder unit 

from the main unit (

→ 

P. 10) 

and discard the citric acid 

water remaining in the lower 

and upper cylinders.

8

Press the [Start|Stop] 

key to start rinsing.

11

Discard the hot water that has collected 

in the lower cylinder.

 

‘

If you are bothered by the smell of the 

citric acid water or if you forgot to put 

water in the upper cylinder in step 

carry out the procedure under “

 Rinsing 

the path inside the main unit with hot 

water.”

13

When three long beeps sound, rinsing is 

complete.

12

Install the cylinder unit onto 

the main unit, locking the 

cylinder unit in place. 

→ 

P. 14

(Do not install the filter or 

water pumping pipe in the 

lower cylinder and do not 

put coffee grounds in it.)

10

Rinse the upper cylinder and add water to 

its two cup scale line.

9

<Switching water>

<Rinsing process>

Recommended time: 

2

 min 30 sec

Off

Blinks

On

On

Light in order from the left

Cleaning with citric acid

Use commercially available food-grade citric acid. Carefully read the safety precautions when using citric 

acid.

 Draining water from the path inside the main unit

 

‘

Drain into the lower cylinder the water remaining in the path inside the main unit.

Rinse the upper and lower cylinders and drain them.

 

‘

Remaining coffee and water will flow into the path inside the main unit.

1

When three long beeps sound, draining is complete.

3

Perform steps 

 to 

 under “

㆓ 

Removing mineral components from the path inside the main 

unit” without inserting water or citric acid.

 

‘

If you insert water, the process for cleaning with citric acid will automatically start. If you insert water by 

mistake, perform steps 

 to 

 under “

㆓ 

Removing mineral components from the path inside the main 

unit.” Once cleaning with citric acid is started, no other menus can be used until rinsing is complete.

2

Discard the water that has collected in the lower cylinder.

4

Summary of Contents for ADS-A02U

























Reviews: