9
10
English
1
Before placing the main unit on
the power plate, remove its lid,
pour water into the main unit using a
separate container, and re-attach
the lid.
How to remove and re-attach the lid.
(Refer to p.11.)
Pour water up to a level below the “full water
level.”
(Refer to p.7.)
2
Lead out the power cord from the
cutout in the power plate, place
the power plate on a
fl
at surface,
and then place the main unit
securely on the power plate.
Check that the power switch is set to “OFF”.
3
Check that the dispense lock
button is at the “Locked” position.
If water is boiled with the dispense lock button
in pressed-down position, it will take longer for
the water to boil and steam may escape from the
spout causing scalds.
How to lock
Sounds heard when dispensing the hot water or
when removing or re-attaching the lid
The “rattling”sound is made by the valve (stopper valve)
that prevents the hot water from spilling out in the event
that the product has been tipped over.
How to adjust the length of the power cord
Adjust the length of the power cord by coiling the cord
around the bottom of the power plate, and lead it out
from the cutout in the power plate.
Lead the power cord out from the cutout.
Caution
●
Do not fill the water directly into the product from a
faucet or place the product on a wet surface so that
its bottom becomes wet.
●
Do not fill the water above “full water level” for boiling.
●
Do not fill the water while the main unit is still in
place on the power plate. Doing so may cause
malfunction.
4
Connect the plug to the power
outlet, and set the power switch
to “ON”
[When the water is boiled]
●
The power switch is automatically at the “OFF”
position, and its boil lamp turns off.
●
Exercise caution as steam will continue to emerge
for a short while.
[When switching off the power while the water is boiling]
Set the power switch to “OFF”
This product does not keep the boiled water hot.
When the water is left inside the product after boiling,
it will cool off.
5
Check that the power switch is
“OFF” and then unplug the plug
from the power outlet.
Function to prevent accidental boiling
without water
When boiling without water, the power switch is set to
“OFF” and the boiling process is stopped.
(Refer to p.14.)
Approximate times taken for boiling water
0.8L
Approx.4minutes
1.0L
Approx.5minutes
∗
The above times are reference values when the
water temperature and room temperature are 23°C,
full water volume and an AC normal rated voltage is
supplied.
Caution
When the main unit is removed from the power plate
while boiling, the boiling process is stopped.
3
Boiling water and dispensing hot water
6
Remove the main unit from the
power plate, and press the dis-
pense lock button to dispense
the hot water.
After the hot water has been dispensed, be
sure to press the dispense lock button to set it
to the “locked” status.
Droplets of water that drip from the vent
on the base of the handle
The product is designed so that the power turns off
when steam is detected. Steam may exit as water
droplets from the vent on the base of the handle,
but this not a malfunction.
Caution
Be sure not to touch the vent on the base of the
handle when repeatedly boiling water or boiling water
in a cool place, as steam or droplets of hot water may
drip from this vent, and scalds may occur.
Do not pour or
splash water over
the power switch.
Pour the water
slowly.
OFF
Main unit
connection
area
Power plate
connection
area
“ Locked” status
“ Unlocked” status
Color line
Cutout
Power Cord
Wind the power
cord around here.
Press
Color line
Click
“ Locked” status
The color line is no
longer visible.
Press
dispense
lock
button
Click
Insert the main
unit straight
down onto the
power plate.
Press
Color line
Click
“ Locked” status
The color line is no
longer visible.
ON
OFF
When the
water is
boiled
Boil lamp illuminates
S type
W type
Boil lamp turns off
