Tiger TIGERFLEX SHIPLAP APEX BIKE SHED General Assembly Instructions Download

Page: 14 / 16

TIGERFLEX

SHIPLAP APEX BIKE SHED ASSEMBLY GUIDE

tigersheds.com

0113 205 4189

sales@tigersheds.com

Step 8:

FELT INSTALLATION

•  Roll out felt along lower part of roof, leaving sufficient
  overhang to fold down onto roof purlin, approx
  75mm/3”.

Do not fold underneath roof.

• Use clout

(CN13)

nails to tack top of felt into the roof panel.

• Repeat for the other side. Fold the overhang at gable
ends under the roof panel and tack in place.

• Ridge piece should overlap the lower strips and
tack into place (if supplied).

Step 9:

BARGE BOARD & FINIAL INSTALLATION

•  Fit Barge Boards to the roof, trapping
  overhanging end of the felt in between
  to create a weatherproof seal.

• Secure together using 2x 40mm

(N40)

nails per Barge Board.

•  Fit Finials at the apex point of the
  Barge Boards. Secure together using
  2x 40mm

(N40)

nails per finial.

CN13

N40

Summary of Contents for TIGERFLEX SHIPLAP APEX BIKE SHED

















Search results

Summary of Contents for TIGERFLEX SHIPLAP APEX BIKE SHED

Reviews:

Related manuals for TIGERFLEX SHIPLAP APEX BIKE SHED

Brands by name

Popular brands

Tiger TIGERFLEX SHIPLAP APEX BIKE SHED, General Assembly Instructions

Search results

Summary of Contents for TIGERFLEX SHIPLAP APEX BIKE SHED

Reviews:

Related manuals for TIGERFLEX SHIPLAP APEX BIKE SHED

Brands by name

Popular brands