background image

ENGLISH – Tiki start

 17

Note that the power-off state, is considered an abnormal situation. 
The battery power is sufficient for another 15 minutes. 
As this alarm of lights and sound emits, the user has to:

 

Leave the hazardous environment

 

Charge the internal battery of the blower unit

 

As necessary, charge the external battery

2.3.4  Filter warning or leak

The indicator light that is closest to the on / off button is on.
The other two (2) indicator lights flash.
The blower emits an alarm sound every one (1) second.
This indicates that either:

 

The inhalation filter is blocked

 

A major leak occurred

In either situation, the user has to:

 

Leave the hazardous environment

 

Evaluate what caused either the leak or the situation with the filter

 

If a situation with the inhalation filter occurred, replace the filter as to: 
5.2 Replace the inhalation filter on page 36

 

If a leak occurred due to a mechanical issue, please replace the faulty parts 
according to the individual instructions in chapter 3 from page 23

 

If a leak occurred to an unknown reason, refer to: 
1.3 Before use on page 5

 

If either the above is the reason for the alarm, contact Tiki Safety AB

Summary of Contents for 1005-51

















































Reviews: