background image

450 Watt Diamond Tile Cutter 

WARNING! PLEASE READ THESE INSTRUCTIONS CAREFULLY 

BEFORE USING THIS TILE CUTTER

 

 

General Safety Rules 

 

Failure to follow all instructions listed below may result in electric shock, fire and/or serious 

personal injury, please read and save these instructions. 

 

Work area 

Keep work area clean and well lit. Cluttered and dark areas invite accidents. Do not operate 

power tools in explosive atmosphere, such as in the presence of flammable liquids, gases or 

dust. Tools create sparks that may ignite such substance. Keep bystanders, children and 

visitors away while operating a power tool. Distractions can cause loss of control. 

 

Electrical safety 

Avoid body contact with grounded surfaces such as pipes, radiators and refrigerators. There is 

an increased risk of electric shock if your body contacts with such grounded surfaces. 

 

Do not expose tools to rain or wet conditions. Water entering a tool will increase the risk of 

electric shock. 

 

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. 

Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords 

immediately to avoid the risk of electric shock. 

 

When operating a power tool outdoors, use an  extension cord suitable for outdoor use. Use of 

a cord suitable for outdoor use reduces the risk of electric shock.   

 

If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) 

protected supply. Use of an RCD reduces the risk of electric shock. 

 

Personal safety 

Stay alert, watch what you are doing and use common sense when operating a tool. Do not 

use tool while tired or under the influence of drugs, alcohol or medication. A moment of 

inattention while operating tools may result in serious personal injury. 

 

Dress properly, Do not wear loose clothing or jewellery. Tie back long hair. Keep your hair, 

clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be   

Summary of Contents for TRP 438











Reviews: