Tile Rite TRP 438 Manual Download

Page: 9 / 10

Technical Specifications

Voltage/Frequency

230-240V~ 50Hz

Motor Power

450W

Duty Cycle

S2:30min

No-Load Speed

5400/min

Blade size

110mm (D) - Bore

22.23mm

Max. Cutting Thickness

To 90

:23mm – to 45

:16mm

Ingress Protection (IP)

IP23

Sound pressure level

92.6 dB(A)

Sound power level

105.6 dB(A)

Symbols

This symbol is known as the 'Crossed-out Wheelie Bin Symbol'. When

this symbol is marked on a product or battery, it means that it should not

be disposed of with your general household waste. Some chemicals

contained within electrical/electronic products or batteries can be

harmful to health and the environment.

Only dispose of electrical/electronic/battery items in separate collection

schemes, which cater for the recovery and recycling of materials

contained within. Your co-operation is vital to ensure the success of

these schemes and for the protection of the environment.

Summary of Contents for TRP 438











Search results

Summary of Contents for TRP 438

Reviews:

Related manuals for TRP 438

Brands by name

Popular brands

Tile Rite TRP 438, Manual

Search results

Summary of Contents for TRP 438

Reviews:

Related manuals for TRP 438

Brands by name

Popular brands