background image

24

WARRANTY PERIOD

The warranty period for the woodchipper commences on the date of sale to the first end user and continues for

a period of 12 months.  This guarantee is to the first end user only and is not transferable except when an 

authorised Timberwolf Dealer has a woodchipper registered with Environmental Manufacturing LLP as a hire

chipper or long term demonstrator – in these situations they are duly authorised to transfer any remaining 

warranty period to their first end user.  Any warranty offered by the Timberwolf Dealer beyond the original 12 month

period will be wholly covered by said Dealer.

LIABILITY

Our obligation under this warranty is limited to repair at Environmental Manufacturing LLP premises or at our op-

tion an Environmental Manufacturing LLP approved Timberwolf dealer.  No liability will be accepted for 

special, indirect, incidental, or consequential loss or damages of any kind. 

WARRANTY STATEMENT

Environmental Manufacturing LLP warrants to the first end user that;

-Your woodchipper shall be designed, built and equipped, at the point of sale, to meet all current applicable 

regulations.

-Your chipper shall be free from manufacturing defects both in materials and workmanship in normal service for

the period mentioned above.
Warranty will not apply to a failure where normal use has exhausted the life of a component.
Engine units are covered independently by their respective manufacturer warranties. 

OWNERS WARRANTY RESPONSIBILITIES

As the owner of an Environmental Manufacturing LLP woodchipper you are responsible for the following;

-Operation of the woodchipper in accordance with the Environmental Manufacturing LLP instruction manual.

-Performance of the required maintenance listed in your Environmental Manufacturing LLP instruction manual.

-In the event of a failure the Environmental Manufacturing LLP authorised Timberwolf dealer is to be notified

within 10 days of failure and the equipment is to be made available for unmolested inspection by the dealer 

technician.

WARRANTY RESTRICTIONS

The Environmental Manufacturing LLP warranty is restricted to the first end user only and is not transferable ex-

cept when an authorised Timberwolf Dealer has a woodchipper registered with Environmental Manufacturing

LLP as a hire chipper or long term demonstrator – in these situations they are duly authorised to transfer any re-

maining warranty period to their first end user.
The Environmental Manufacturing LLP warranty may be invalidated if any of the following apply;

-The failed parts or assembly is interfered with in any way.

-Normal maintenance has not been performed.

-Incorrect reassembly of components.

-The machine has undergone modifications not approved in writing by Environmental Manufacturing LLP.

-In the case of tractor driven equipment, use has been on an unapproved tractor.

-Conditions of use can be deemed abnormal.

-The machine has been used to perform tasks contrary to those stated in the Environmental Manufacturing LLP in-

struction manual.

WARRANTY SERVICE

To obtain warranty service please contact your nearest  Environmental Manufacturing LLP approved Timberwolf

dealer.  To obtain details of the nearest facility please contact Environmental Manufacturing LLP at the address

on the front of this manual.

These warranty terms are in addition to and not in substitution for and do not affect any right and remedies which

an owner might have under statute or at common law against the seller of the goods under the contract by which

the owner acquired the goods.

ENVIRONMENTAL MANUFACTURING  LLP 12 MONTH CHIPPER WARRANTY

WARRANTY STATEMENT

TIMBERWOLF

TW 190TDHB

Summary of Contents for TW 190TDHB




















































Reviews: