pm2:33
CTMR
RPT : 20 : 00
Press repeatedly until
RPT (repeat)
STEP 3:
S
et
to One
Countdown, to
Repeat, or to
Count-Up
pm2:33
CTMR
C-UP : 20 : 00
Count-Up
(after countdown
is complete)
pm2:33
CTMR
: 20 : 00
One countdown
only (blank on left)
STEP 4:
S
tart
Countdown
(if timer doesn't
start, press Enter
then press Mode
to start)
NOTE: You can
press Mode after
setting 1, 2, or more
Alerts; then to start
the timer, press
Enter once, and
Mode once.
Press to save all
programming and start
countdown session
pm2:33
CTMR
C-UP : 19 : 33
6. How to use the Custom Timer.
First set a countdown time of from 3 seconds to 60 minutes. Then program up to 6
unique alerts to signal within this countdown time. The countdown time can be set to countdown once, to repeat over and over,
or to count-up after countdown completes. NOTE: If you set an alert at 10 minutes, it will signal when there are 10 minutes left
in the countdown; set an alert at 1 second to signal at the end of countdown.
STEP 1:
Program
Countdown
Time
pm2:33
CTMR
TIME :
40
:30
Adjust minutes
(countdown time =
40 minutes & 30 seconds)
pm2:33
8-13
CUSTOM TMR
Advance to
CUSTOM TMR
pm2:33
CTMR
TIME: 00 :
30
Adjust seconds
pm2:33
CTMR
TIME :
00
:30
Advance to
minutes
pm2:33
CTMR
TIME 00 :
00
Enter
adjustment
mode
Proceed to
STEP 2
below
Alert A
= 5 second vibration... or if alert switch (on the side of the unit) is set to beep = 1 beep
Alert B
= 5 second vibration, 5 second space, 5 second vibration…………or……….. = 2 beeps
Alert C
= 10 second vibration………………………………………………or………. = 3 beeps
Alert D
= 10 second vibration, 7 second space, 10 second vibration………or……… = 4 beeps
Alert E
= 20 second vibration………………………………………………or……… = 5 beeps
Alert F
= 2 second vibration……………………………………………… or……… = 6 beeps
STEP 2:
Program up to
6 alerts within
countdown
time
pm2:33
CTMR
A : 00 : 00
Advance to
Alert A
pm2:33
CTMR
A :
00
:01
Advance to
minutes
pm2:33
CTMR
A :
01
: 01
Adjust minutes
pm2:33
CTMR
B : 00 : 00
Advance to
Alert B
Set Alert B the
same way as you
set A. You can
set one or all of
the alerts
A,B,C,D,E,F.
After setting the
alerts you want,
proceed to
STEP 3 below
TIP: To skip an
alert during
programming,
press the Enter
button two times
pm2:33
CTMR
A : 00 :
01
Adjust seconds
Stop
Count-
down
This action
stops the timer
and puts it in
the ready
position to
start again
pm2:33
CTMR
C-UP : 20 : 00
Press two middle buttons
simultaneously
for 1 second
or less
to stop countdown
Exit
Mode
Restart
count-
down
Press to restart
countdown
pm2:33
CTMR
C-UP : 19 : 49
Press two middle
buttons simultaneously
and hold for 2
seconds
to exit mode
pm2:33
8-13
CUSTOM TMR
Then
ERASE
ALL
program-
ming
pm2:33
CTMR
ERASEALL=T
Hold for 3seconds
pm2:33
8-13
CUSTOM TMR
Start from here
pm2:33
CTMR
ERASED ALL
Press to erase
Restarting
Timer when
it is
programmed
pm2:33
T 08:00
ADB
Press to enter
Press to start
pm2:33
CTMR
C-UP : 19 : 49
pm2:33
8-13
CUSTOM TMR
Start here
NOTES for the Custom Timer:
1.
During programming, once you have selected all the alerts you need, you can press Mode at any time to save your programming. To
start the timer, press
Enter
once, then
Mode
once.
2.
Once the custom timer is programmed, it will remain programmed until all programming is erased.
3.
To restart timer after countdown completes for one-time countdown or for count-up, press
M
to restart (at any time during count-up).
4.
Set any alert to 1 second to have a signal at end of countdown.
5
. From "CUSTOM TIMER" you can press
Enter
and wait until ready to start countdown by pressing
Mode
.
Checking and changing programming (without erasing all programming)
pm2:33
8-13
CUSTOM TMR
Start here
pm2:33
T 08:00
#A= 01:00
Press and hold for
3 seconds to see
alerts
pm2:33
T 08:00
#B= 01:00
Press to scroll
through existing
alerts
pm2:33
T 08:00
#B= 01:00
Push
simultaneously
to allow this alert to
be changed
pm2:33
T 08:00
#B= 01:15
Press to
change
seconds
pm2:33
T 08:00
#B= 01:15
Advance to minutes
pm2:33
T 08:00
#B= 03:15
Press to accept
changes. Press
again to exit mode
pm2:33
T 08:00
#B= 03:15
Press to
change
minutes
