background image

TMS6002 
USER MANUAL 

Ref :  MN06127 

Date :  2019-03-27

 

Issue :  A1 

Page:  7/18 

 

Tous droits réservés © TimeLink microsystems

 

 

Section [IP_eth0] 

Name 

Description 

Availability 

Default value 

Accepted values 

Ip 

IP V4 address of the 
equipment 

Mandatory 

192.168.10.190 

Any compliant IP V4 
address 

mask 

Subnet mask of the 
network on which the 
equipment is connected 

Mandatory 

255.255.255.0 

Any compliant subnet 
mask 

gateway 

IP V4 address of the 
default gateway 

Optional but 
recommended 

192.168.10.254 

Any compliant IP V4 
address 

nameserver 

IP V4 address of the name 
server 

Optional 

8.8.8.8 

Any compliant IP V4 
address 

 

[SOURCE_PRIORITIES] Section

 

Name 

Description 

Availability 

Default value 

Accepted values 

GNSS 

Select the priority of the 
source compare to the 
others. 1 is highest priority 

Mandatory 

1,2,3 

IRIGB_IN 

Select the priority of the 
source compare to the 
others. 1 is highest priority 

Mandatory 

1,2,3 

LOCAL 

Select the priority of the 
source compare to the 
others. 1 is highest priority 

Mandatory 

1,2,3 

 

[GNSS] Section

 

Name 

Description 

Availability 

Default value 

Accepted values 

PRESENCE 

Enable/disable the GNSS 
source. 

Mandatory 

Y, N 

UTC_OFFSET 

Offset between GPS and 
UTC time in second 

Mandatory 

18 

Number 

MOBILE 

Enable the GNSS mobile 
receiver mode 

Mandatory 

Y

 or 

N

 

LEAP_MODE 

Set the way the UTC offset 
update is managed. 

LEGACY: the parameter 
UTC_OFFSET described 
above is prioritized and 
when different from the 
one propagated by GNSS, 
an alarm is triggered. 
Manual acknowledgement 
is then necessary to switch 
to the GNSS parameter.  

AUTOMATIC: as soon as 
available the UTC offset 

Mandatory 

AUTOMATIC 

LEGACY

 or 

AUTOMATIC

 

Summary of Contents for MN06127



















Reviews: