2
ENGLISH 329-0950-00
Register your product at www.timex.com
a.
In your smartphone’s settings (not the Timex app), view
Bluetooth
®
devices.
b.
Have your smartphone un-pair (“forget” or disconnect) your iQ+
Move MULTI-TIME watch.
c.
Exit the Bluetooth
®
settings.
d.
Open the Timex Connected app and sync watch and
smartphone.
SHOWING SECONDS, DATE, DISTANCE, STEPS
By default, the second hand shows seconds as on any analog watch.
When the second hand is set to show seconds, pressing the crown
temporarily causes the second hand to point to the current day of the
month; for example, at 23 seconds past the minute, pressing the crown
would cause the second hand to point to 10 on the tenth day of the
month.
You can set the second hand to show, instead of seconds, the number of
steps, distance, day of the month, or 3
rd
Time Zone in 24 Hour Format.
These settings are in the smartphone app.
ALARM
Set and turn on daily alarm on smartphone app. Sync to send alarm
setting to watch. When alarm sounds, night-light flashes on watch. Press
crown to silence, if crown is not pressed, alarm will sound for 20 seconds.
COUNTDOWN TIMER
Set and start Countdown Timer on smartphone app. Sync to send to
watch. Watch beeps and night-light flashes when countdown ends. Press
crown to silence, if crown is not pressed, alert will sound for 20 seconds.
ADJUSTING STRIDE LENGTH
The Timex iQ+ Move Multi-Time uses an algorithm for distance
measurement which automatically determines your stride based on your
height and speed. If you find the distance reported does not match your
actual walking or running distance, you can calibrate the distance by up
to +/- 25% via the smartphone app. You can do this through the distance-
adjustment option on the watch section of the app.
LOW BATTERY POWER
The watch indicates when you need to replace the battery:
•
During synchronization of the watch with the smartphone, the app will
alert you if the battery needs to be replaced soon.
•
The watch second hand will begin to move every 2 seconds in 2-
second increments until the battery is replaced.
When battery power is low:
•
To conserve power, the INDIGLO
®
night-light will not function until the
battery has been replaced.
•
The watch and smartphone will not communicate.
The activity tracking functions will remain functional until the battery has
been completely depleted, but new data will not be stored.
REPLACING THE BATTERY
Before replacing the battery, it is recommended that you synchronize to
the smartphone app to ensure you have retrieved all of the latest activity
and sleep data from the watch. After the battery is replaced, the watch
will need to be re-calibrated with the smartphone.
STORING THE WATCH
You may remove power from the watch for storage. To do this, pull the
crown out to the outer position. With the crown in this position, the hour,
minute and second hands will stop immediately, and the activity- and
sleep-tracking functions will be inactive after 30 minutes.
SMARTPHONE APP UPDATES
As smartphone app updates become available, you will be notified on
your smartphone, the same way you learn of updates to other
smartphone apps. Update this app using the same process you would to
update any other app. Specific process varies by smartphone.
WATCH UPDATES
As watch updates become available, you will be notified in the Timex
Connected smartphone app. Follow the instructions in the app.
NOTE: Because the update will delete all activity recorded for the
current day, performing the update early in the day will minimize the
loss of recorded activity.
To ensure an uninterrupted connection during the update, place the
watch and smartphone on a flat surface, beside each other, and avoid
moving them until the update completes. During the update, the lower
subdial hand shows progress, from 0 to 100%.
The duration of the update varies, averaging 5 to 10 minutes, but
sometimes lasting up to 30 minutes.
WATER RESISTANCE
WARNING: TO MAINTAIN WATER RESISTANCE, DO NOT
PRESS ANY BUTTONS UNDER WATER.
NOTE: To confirm that your watch is water resistant, check for the
symbol before immersing in water.
Your iQ+ Move Multi-Time watch is water resistant to a depth of 50
meters (164 feet).
•
The watch is water resistant only as long as lens, push buttons and
case remain intact.
•
The watch is not a diver watch and should not be used for diving.
•
Rinse the watch with fresh water after exposure to salt water.
Water Resistance Depth
p.s.i.a.* Water Pressure Below Surface
30m/98ft
60
50m/164ft
86
100m/328ft
160
200m/656ft
284
* pounds per square inch absolute
TIMEX INTERNATIONAL WARRANTY
http://www.timex.com/productWarranty.html
.
FCC NOTICE (U.S.) / IC NOTICE (CANADA):
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
This device complies with Industry Canada license exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada.
DECLARATION OF CONFORMITY
Manufacturer’s Name:
Timex Group USA, Inc.
Manufacturer’s Address:
555 Christian Road
Middlebury, CT 06762
United States of America
declares that the product:
Product Name:
Timex
®
iQ+
®
Move Multi-Time
Model Numbers: M328
is in conformity with the relevant EU harmonized legislations.
This declaration is issued under the sole responsibility of the
manufacturer and conforms to the following:
