background image

 

11

The weather station uses the air pressure data of the last four hours to create a 
weather forecast for the next 12 to 24 hours.  
 
It must be taken into account that the date within the first twelve hours after 
inserting the batteries will not be correct, as the weather station has to get used 
to the environmental circumstances after the restart. The forecast can be given 
for a radius of up to 15-20 KM (9 to 12 miles

). 

When forecasting the weather, the 

station uses five different symbols: sunny, light cloud cover, cloudy, rain and 
stormy. In addition, a snowflake is displayed when the outdoor area temperature 
drops below minus four (-4°) degrees Celsius 

(

25°F). 

 

BATTERY LEVEL DISPLAY 
The weather station display also displays the battery level to show whether the 
batteries of the weather station or the outdoor sensor need to be replaced.  

• 

Battery level display of the weather station: in the clock area of the 
display. 

• 

Battery level display of the outdoor sensor: in the Outdoor area of the 
display. 

 

 

BACKLIGHT 
Briefly press the “SNOOZE/LIGHT” button to activate the LED display backlight 
for five seconds. 
 
RADIO FREQUENCY CONNECTION TO OUTDOOR SENSOR 

• 

Press the “CHANNEL” button to select a channel (1 to 3). This gives you 
the option of polling three outdoor sensors with one weather station.

 

• 

Press and hold down the “CHANNEL” button for three seconds to search 
for outdoor sensors. You can break off this operation by briefly pressing 
the “CHANNEL” button. 

LOCATION/TIDES DISPLAY/MOON PHASE/SUNRISE AND SUNSET DISPLAY 

• 

Press and hold down the “LOC” button for three seconds until the city 
selection begins to flash. Use the arrow keys “

 & 

” to set your location. 

You can see the list of all cities on the next page. 

• 

Press ”LOC” to confirm your setting. 
The weather station now uses the saved data on the selected city to 
determine the sunrise and sunset times, the strength of the tides and the 
phrases of the sun and moon.  

SUNRISE SUNSET –  
   Press and hold the “LOCATION” button for three seconds. The city name will 
be flash. Press “+” or “-“ change the city. The sunrise and sunset time will be 
automatic change. 

SUNRISE SUNSET CITIES OR STATE DESIGNATION 
CITY/STATE Designation CITY/STATE Designation CITY/STATE Designation
Anchorage, 
Alaska 

ALA Little 

Rock, 

AR 

LIT Raleigh, 

NC 

RDU 

Atlanta, GA 

ATL 

Lincoln, NE 

LNK 

Richmond, 

RIC 

Summary of Contents for TX6180





















Reviews: