background image

 

 

Touchtone 

Daily alarm with automatic snooze alert (5 minutes) 

• 

Crescendo alarm 

• 

Alarm time 120 seconds 

 

Automatic DST function. 

Weekly day indicator in English 

Battery power indicator for outside sensor 

Thermometer 

• 

Measuring range inside temperature 0 degree C (32º F)º – 50 degree C (-58º F)  

• 

Measuring range outside temperature – 50 degree C (-58º F) to 70 degree C (158º 
F) 

• 

Offers three channels for wireless transmission. One sensor included. Additional 
sensors available from manufacturer.   

• 

Transmission per 433.92 MHZ frequency 

• 

Trend indicator of the inside and outside temperature 

• 

Storage of the minimum and maximum values for inside and outside temperature 

Temperature shown in Celsius (C) degrees or Fahrenheit (F) degrees 

Temperature alarm when temperatures reach pre- set temperature 

LED background display lighting 

Transmission range radius of outside sensor of about 25 meters (82 Feet) 

Batteries Required (Batteries included) 

             *     Weather station 2x AAA/UMA/ LR03         

• 

Outside sensors 2x AAA/UMA/LR03 

 
Display 
 
Displays the hours, minutes, seconds, month, date, day, (in English), alarm, inside and outside 
temperature. 
 
To start up 
To activate 
 

• 

Open the battery compartment on the back of the outside sensors and install the 
batteries matching the marked polarity.  Replace the battery compartment. 

• 

Open the battery compartment at the backside of the base weather station and 
install the batteries matching the marked polarity.  Close the compartment. 
+     When installing the batteries a short display of all the functions will appear and 
a signal tone will sound. 

• 

The base weather station will now start to establish a connection with the outside 
sensor.  This will take about 3 minutes and will display a blinking receiver indicator 
in the display area of the outside temperature. 

• 

After the base weather station makes the connection with the outside sensor, it will 
automatically receive the temperature transmission signal.   This will take about 7 
minutes and will be displayed with a blinking transmission tower symbol in the 
display by showing the time. 

 
 
 

• 

FOR RADIO CONTROL CLOCKS TX6000RC ONLY - After successful reception 
the transmission tower symbol will be shown continuously in the display. 

 
When you have successfully completed the automatic setting process, use a sharp object to 

Summary of Contents for TX6180





















Reviews: