background image

 

 

 
 
Setting of the temperature alarm. 
 
Push and hold the push button “temp” for 3 seconds. 
The channel indicator begins to blink. Now set with ”Channel” (“Kanal”) the desired channel. 
     +     Push “temp” to verify 
 
 
The symbol for the upper limit of the terminal alarm begins to blink. Now set with “

 & 

” 

the 

desired maximum. 
     +     Push “temp” to verify 
The symbol for the lower limit of the terminal alarm begins to blink. Now set with “

 & 

” the 

desired minimum. 
     +     Push “temp” to verify and close the setting 
 
Activate and deactivate the temperature alarm. 
     To activate or deactivate the daily alarms, push the “temp” button quickly. 
               +     Alarm activated          temperature alarm symbol on display 
               +     Alarm deactivated      temperature alarm symbol disappears 
 
Information 
 

• 

The clock changes after 8 seconds, without touching push button, automatically 
from setting mode to normal time mode. 

• 

The alarm sounds, as soon as the temperature reaches the limits set for the 
temperature and stops, as soon as the actual temperature differs by more than 1 
degree C from the preset settings.  Parallel In conjunction with the signal sound will 
the symbol for the temperature alarm will start blinking. 

 

• 

Setting limits, channel 1-3 temperatures C (-58º F) to 70 degree C (158º F) 

 
 
Automatic snooze alarm. 
 
     To activate the automatic snooze alarm, please proceed as follows: 
              While the alarm sounds, push the push button  (Snooze/Light) to activate the snooze 
alarm function.  When the snooze alarm function is activated “Zz” symbol shows on display. 
              The alarm will with this procedure delay it by 5 minutes and restarts after that. The 
automatic snooze alarm can with every desired push button touch be stopped and for up to a 
maximum four times be reseated. 
 
12/24-hour mode. 
      The time indicator can follow a 12 or 24-hour format. By a quick touch of the “

 & 

 “ button 

one can   decide between the 2 modes. 
 
 
Degrees Celsius (C)/Degrees Fahrenheit (F) temperature indicator. 
     Degrees C or Degrees F.  By quick touch of “” push”

 button, you can decide between the 

two modes. 

 
Temperature trend indicator. 
     After insertion of the batteries, the weather station misses will not immediately record the 

Summary of Contents for TX6180





















Reviews: