background image

 

 

actual temperature.  The trend indicator shows a neutral course (average) of the temperature.  (A 
horizontal arrow) 
 
      The ongoing operation of the temperature indicator is determined as follows. 
              When the temperature after one hour departs varies more than 1 degree C over the first 
measured value, a positive operation will be shown (upward pointing arrow) 
              When the temperature after one hour departs varies more than 1 degree C under the 
first measured value a negative operation will be shown (a down pointing arrow) 
 
Maximum/minimum temperature. 
 

• 

Quickly touch maximum push button to show the maximum and minimum 
temperature. 

               The indicator changes back to the normal time indicator mode after 5 
seconds. 
 

• 

Through the pushing and holding of the “maximum” button you can activate the 
maximum temperature. 

• 

Through quick push of “snooze/ alarm” button light you can activate the background 
light on the display for 5 seconds. 

 
 
Lighting. 
 
Through quick push of the snooze/light alarm push button you activate the background light of the 
display for 5 seconds. 
 
During alarm the display will automatically light up for 5 seconds. 
 
 
Transmission connection to outside sensor. 
 

• 

Push the channel button to select a channel (1 to 3) 

            You have the possibility to choose 3 outside channels with one weather station. 

• 

Push and hold the channel button for 3 seconds to search for outside sensors. 

 
 
 
FCC COMPLIANCE 

---

This device complies with Part 15 of the FCC Rules. Operation is subject 

to the following two conditions: (1) This device may not cause harmful interference, and (2) This 
device must accept any interference received, including interference that may cause undesired 
operation.  
 
WARNING: Changes or modification to this unit not expressly approved by the party responsible 
for compliance could void the user's authority to operate the equipment. 
 
NOTE: This   equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates 
uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
  

Summary of Contents for TX6180





















Reviews: