background image

 

6

 
 
 

 

 
 

 
To Get Started, Please Follow The Direction Below  

• 

Remove the bracket from the outdoor sensor case. Open the battery 
compartment by unscrewing the four attachment screws on the back of 
the outside sensor.     Install the batteries matching the marked polarity.  
Note the two buttons above the battery cradle. One marked “C°/F°” and 
the other marked “Tx”. The Celsius (C) or Fahrenheit (F) Scale can be 
selected for the LCD readout of this remote sensor by pressing the C/F 
button. When you press the Tx button this will confirm that there is 
transmission of temperature data by displaying a satellite icon in the 
bottom left corner of the Remote Sensor LCD Display.  Not until you see 
the icon in the sensor display is the unit transmitting temperature data. 
Once that icon appears it is okay to seal the battery compartment. 
Replace the battery compartment door by carefully securing that door with 
the four screws. It is important to make the seal as tight as possible on this 
door. During the setup, keep the outdoor sensor close to the base station 
in order to establish an effective wireless transmission. Do not 
permanently install the remote sensor until transmission has been 
confirmed

.  

• 

Open the battery compartment on the rear side of the base weather 
station and insert the batteries again observing the correct polarity. Close 
the battery compartment. 

 

• 

When you insert the batteries all the symbols on the display will briefly 
light up and you will hear a signal tone. 

 

• 

The weather station will now start to   connect to the outdoor sensor and 
thus ready to begin transmitting data.  This operation takes about three 
minutes and is displayed by a flashing reception symbol in the 

OUTDOOR” display area.

 

• 

After the weather station has created a connection to the outdoor sensor, 
it will then commence automatic reception of the WWVB Radio Signal for 
the Radio Controlled Clock.  This operation could take up to twenty-four 
hours

 

and completion of which is displayed by the flashing radio mast 

symbol in the “Clock” display area. The best time to catch the radio time 
signals from Ft. Collins, Colorado is between 2AM and 5AM.  

• 

If reception is successful, then the radio mast symbol will appear 
continuously in the display.  

 

If this automatic setting process is unsuccessful, then use a sharply pointed 
instrument to press the Reset button on the rear side of the weather instrument.  
 

Summary of Contents for TX6180





















Reviews: