background image

5. 

DISPLAY AND CONTROL ELEMENTS OF THE LUBRICATION SYSTEM

5.1 Display 

Elements

The operating status of the C-Power can be determined via the green or red LED and the display 
screen on the C-Power unit (refer to figure 8). The C-Power offers a menu-guided setting. Changes 
to settings are shown on the display. Error messages also are indicated on the display.

Figure 8

5.2 

Function Indication on the Display

The display is located on the C-Power unit (refer to figure 8, chapter 5.1). The display shows settings, 
operating conditions and error messages.

When no errors are present, the display shows the remaining volume of the mounted C-Power LV-unit 
in percent volume (% Vol.). Figure 9 shows an example of the information that will be displayed if the 
C-Power LV-unit is new and full.

Figure 9

The display cannot be switched off by the operator. If the lubrication system is switched off, 
the display will always show two lines (see figure 10 below).

Figure 10

5.3 

Function Indication via the LED signal lights

Table 2

12

99

% Vol.

– –

MODE
SAVE
push button

Connector for
distributor MP 6

Green LED

LCD

Red LED

ON/OFF
SELECT
push button

Summary of Contents for C-POWER 250





























Reviews: