13
2. Connection of Boom Barrier and putting it into operation
In further description of Boom Barrier
connection to control unit and other devices, connection and wiring
diagrams the maximum configuration of accessories and options are specified.
When in particular separate configuration some components are not used, then they just are not
connected or not taken into account.
The additional options
are as follows:
-
Heating with heating thermostat.
It
is used in case of frost.
-
Cooling fan with
cooling thermostat.
It
is used in case of hot at the installation site.
-
Audible alarm.
It
is an additional option to be installed on the Boom Barrier.
-
Radio controller of wireless remote control.
It
is an additional option to be used for road
blocker wireless control from remote control panels (remote control pendants).
-
Induction loop controllers.
It
is an additional option to be used for connection of induction
loops to prevent the Boom Barrier raising when a vehicle is under boom.
All optional device of control units and Boom Barrier which can be unused and are options are
marked with
"*"
on diagrams.
Limit switches
are used as the Boom Barrier
s ’
up and down position sensors.
2.1. Connection of Boom Barrier and putting them into operation
After the Boom Barrier installation the control unit is connected
230VAC
power supply network via
safety switch
B6. Circuit Breaker
placed in convenient location.
The differential breaker
10А 30мА
to be used as switch (overload and leakage protection), such as
ABB
DS951 C10-30MA/AC
.
Control signals (for example, access control system), remote control panel B4-
А1. Remote Control Unit
PCB111 (optional), emergency "Stop" button B5-
А1
, Remote Emergency Push Button "Stop" ASCO XAL-
J174 and actuating devices, for example,
traffic lights, external siren
are connected to control unit.
General connection diagram of the Boom Barrier and additional devices is shown in
Annex 1
.
Wiring diagram of the Boom Barrier with control unit and additional devices is shown in
Annex 2
.
The switch
B6-K1. Circuit Breaker,
the emergency stop button
B5-
А1.
Remote Emergency Push
Button "Stop"
to be connected to the control unit. The wire remote control panel
B4-
А1.
Remote Control
Unit RB111
1
and other additional devices, such as
traffic lights
or
access control system
, can be
connected.
The emergency stop button
B5-
А1. Remote Emergency Push Button "Stop"
and remote control panel
B4-
А1. Remote Control Unit
RB111*
are installed at the road blocker operator workstation.
The supply voltage
230VAC
to be connected and the switch
B6. Circuit Breaker
to be ON after
completion of the Boom Barrier installation, boom balancing and all connections.
Trial raising and lowering of Boom Barrier to be initiated after completion of all connections and
energization. Proper operation to be controlled. If the Boom Barrier operation is improper, then the cause to be
found and the problem to be remedied using
Table 12
.
The Boom Barrier has an automatic boom raising function, when it does not reach the down position
during lowering (comes up against obstacle, down position sensor is not actuated).
The automatic boom raising function during coming up against obstacle is activated with the switch
SW1
.
The Boom Barrier has a boom deceleration function upon completion of opening or closing.
The deceleration function is activated with the switch
SW2
.
The
SW3
switch position determines the deceleration duration during raising. When it is ON - 1 second,
when it is OFF- 2 seconds.
The
SW4
switch position determines the deceleration duration during lowering. When it is ON - 1 second,
when it is OFF- 2 seconds.
1
The differential breaker
10А 30мА
to be used as switch (overload and leakage protection), such as
ABB DS951 C10-
30MA/AC
.
