Titan 0552600, Owner'S Manual

English

English

© Titan Tool Inc.  All rights reserved. 

3

Important Safety Information

•  This system is capable of producing 3300 PSI / 228 Bar.  Only 

use replacement parts or accessories that are specified by the 

manufacturer and that are rated a minimum of 3300 PSI.  This 

includes spray tips, nozzle guards, guns, extensions, fittings, and 

hose.

•  Always engage the trigger lock when not spraying.  Verify the 

trigger lock is functioning properly.

•  Verify that all connections are secure before operating the unit.

•  Know how to stop the unit and bleed pressure quickly. Be 

thoroughly familiar with the controls.  Pressure will not be 

released by turning off the motor.  The PRIME/SPRAY valve 

or pressure bleed valve must be turned to their appropriate 

positions to relieve system pressure.  Refer to PRESSURE RELIEF 

PROCEDURE described in the pump manual.

•  Always remove the spray tip before flushing or cleaning the 

system.

NOTE TO PHySIcIaN: 
Injection into the skin is a traumatic injury which can lead to 

possible amputation. It is important to treat the injury as soon as 

possible. DO NOT delay treatment to research toxicity. Toxicity 

is a concern with some coatings injected directly into the blood 

stream. consultation with a plastic surgeon or reconstructive hand 

surgeon may be advisable. 

warNING:  HaZarDOuS VaPOrS
Paints, solvents, insecticides, and other materials can 

be harmful if inhaled or come in contact with the body.  

Vapors can cause severe nausea, fainting, or poisoning.

PrEVENTION:

•  Use a respirator or mask if vapors can be inhaled.  Read all 

instructions supplied with the mask to be sure it will provide the 

necessary protection. 

•  Wear protective eyewear.

•  Wear protective clothing as required by coating manufacturer.

warNING:  GENEraL 
Can cause severe injury or property damage.

PrEVENTION:

•  Always wear appropriate gloves, eye protection, clothing and a 

respirator or mask when painting.  

•  Do not operate or spray near children.  Keep children away from 

equipment at all times.

•  Do not overreach or stand on an unstable support.  Keep effective 

footing and balance at all times.

•  Stay alert and watch what you are doing.

•  Do not operate the unit when fatigued or under the influence of 

drugs or alcohol.

•  Do not kink or over-bend the hose. Airless hose can develop leaks 

from wear, kinking and abuse.  A leak can inject material into the 

skin.  

•  Do not expose the hose to temperatures or pressures in excess of 

those specified by manufacturer.

•  Do not use the hose as a strength member to pull or lift the 

equipment.

•  Use lowest possible pressure to flush equipment.

•  Follow all appropriate local, state and national codes governing 

ventilation, fire prevention and operation.

•  The United States Government Safety Standards have been 

adopted under the Occupational Safety and Health Act (OSHA).  

These standards, particularly part 1910 of the General Standards 

and part 1926 of the Construction Standards should be consulted.

•  Before each use, check all hoses for cuts, leaks, abrasion or 

bulging of cover.  Check for damage or movement of couplings.  

Immediately replace hose if any of those conditions exist. Never 

repair a paint hose.  Replace with a conductive high-pressure 

hose.

•  Do not spray outdoors on windy days.

•  Always unplug cord from outlet before working on equipment 

(electric models only).

Specifications

Gallons per minute (GPM) 1.15 (4.35 LPM)
Maximum tip size

1 gun - 0.033”
2 gun - 0.021”

Maximum pressure

3300 PSI (22.8 MPa)

Power

2.5 HP Brushless DC Motor, 100~120V 

AC, 50/60Hz, 15A

Weight, high rider

98 lbs. (44.5 kg)

Maximum hose length

300’ (91.4 m)

Generator requirement

5000 Watt, 20A, sine wave generator, 

idle-down feature disabled

Table of contents

Safety Precautions ........................................................................... 2

General Description ........................................................................ 4

Operation ......................................................................................... 4

Locking the Spray Gun ...............................................................................4

Pressure Relief Procedure ..........................................................................4

 Setup .................................................................................................................5

Preparing to Paint.........................................................................................5

 Painting ............................................................................................................6

Control Panel Indicators .............................................................................6

Spraying ........................................................................................... 7

Spraying Technique .....................................................................................7

 Practice .............................................................................................................7

Clearing the Spray Tip .................................................................................8

cleanup ............................................................................................ 8

maintenance .................................................................................... 9

General Repair and Service Notes ..........................................................9

Replacing the Filters ..................................................................................10

Replacing the Motor Assembly .............................................................10

Replacing the Gears ...................................................................................10

Replacing the Transducer ........................................................................10

Replacing the PRIME/SPRAY Valve .......................................................11

Servicing the Fluid Section ......................................................................12

Replacing the Complete Fluid Section Assembly ...........................13

Troubleshooting ............................................................................ 14

Parts Listings .................................................................................. 44

Main Assembly ............................................................................................44

Drive Assembly ............................................................................................46

Upright Cart ..................................................................................................47

Fluid Section Assembly ............................................................................48

Filter Assembly ............................................................................................50

Labels ..............................................................................................................51

Electrical Schematic ...................................................................................51

 Accessories ....................................................................................................52

Product registration ..................................................................... 53

warranty ........................................................................................ 56