background image

 

GENERAL WARNING 

 

     

 

 

 

GENERAL WARNINGS

 

 

 

READ and UNDERSTAND this manual completely before using the Manure Spreader.  

 

Operators must read and understand all safety and warning information, operating 
instructions, maintenance, and storage instructions before operating this equipment. 
Failure to properly operate and maintain the manure spreader could result in serious 
injury to the operator or bystanders.  
 

OPERATION WARNINGS 
  

 

Never carry passengers.  

 

Do not sit or stand on the manure spreader. 

 

Do not allow children to play on, stand upon or climb on the manure spreader.  

 

Always inspect the manure spreader before use for missing or loose hardware.  

 

Replace or repair damaged or worn parts immediately. 

 

Always check and tighten hardware and assembled parts before operation. 

 

Avoid large holes and ditches when transporting loads. 

 Be careful when operating on 

steep grades (hills) as the manure spreader may tip over. 

 

Do not pull close to creeks, ditches, or public highways.  

 

Do not use the manure spreader in windy conditions.  

 

Always use caution when loading and unloading the manure spreader.  

 

Only tow the manure spreader using a lawn tractor, ATV or golf cart at a speed of no 
greater than 5 mph for spreading. Crush and Cut Hazards  

 

Always keep hands and feet clear from moving parts while operating the manure 
spreader. 

 

Always keep the work area clean and clear of debris. 

 

Always wear safety gear, eye protection, gloves and work boots while operating the 
manure spreader. 

 

CRUSH AND CUT HAZARDS  
 

 

Always keep hands and feet clear from moving parts while operating the manure 
spreader.  

 

Always keep the work area clean and clear of debris.  

 

Always wear safety gear, eye protection, gloves and work boots while operating the 
manure spreader 

 

 

 

Summary of Contents for 191396



















Reviews: