10
© SprayTECH. All rights reserved.
English
Optional accessories
Part Number Description
0276254
Projector set, #2 complete
0276227
Projector set, #3 complete
0276228
Projector set, #4 complete
0276229
Projector set, #5 complete
0276245
Projector set, #6 complete
0524211
Projector set, #7 complete
0277090
Projector set, low air flow, #2A complete
0277091
Projector set, low air flow, #3A complete
0277092
Projector set, low air flow, #4A complete
0277093
Projector set, low air flow, #5A complete
0277094
Projector set, low air flow, #6A complete
0276449
Air cap, #2
0276452
Air cap, #3
0276455
Air cap, #4
0276458
Air cap, #5
0276417
Air cap, #6
0524401
Air cap, #7
0295641
Air cap, low air flow, #2A
0295642
Air cap, low air flow, #3A
0295643
Air cap, low air flow, #4A
0295644
Air cap, low air flow, #5A
0295645
Air cap, low air flow, #6A
0276446
Nozzle, #2
0276451
Nozzle, #3
0276454
Nozzle, #4
0276457
Nozzle, #5
0276418
Nozzle, #6
0524363
Nozzle, #7
0276447
Needle assembly, #2
0276453
Needle assembly, #3
0276456
Needle assembly, #4
0276459
Needle assembly, #5
0276244
Needle assembly, #6
0524210
Needle assembly, #7
0508124
Cover, clip-on, 1 quart
0279942
Tip accessory kit
0279941
Deluxe tip accessory kit
NOTE: The “low air flow” projector sets and air caps are
suitable for low cFM compressors.
Repair kits
Part Number Description
0297051
Check valve repair kit (Includes 3 assemblies)
0276257
Check valve membrane kit
(includes 10 membranes)
0297052
Gasket, cup, white (includes 6 gaskets)
0276258
Gasket, cup, Thiokol - black (includes 6 gaskets)
0277943
HVLP gun repair kit
Includes
:
• front air valve seal
• rear air valve seal
• needle packing
• air control valve o-ring (2)
• check valve assembly
• check valve tube, short
• check valve tube, long
• cup gasket
Material Reduction/Projector Set chart
Before spraying, the material being used must be thinned with an appropriate solvent and the proper projector set must be installed. It
is always best to follow the material manufacturers recommendations and thinning procedures.
There are two simple methods of measuring the proper thickness of a material:
1. Dip a paint stick into the material and remove it, watching carefully as the material runs off. When the material begins to form
drops, the drops should fall about 1 second apart.
2. Use a viscosity cup (P/N 0153165). Dip the cup into the material and remove it. Use a watch or clock to time how long the
material drains from the cup in a continuous stream. Once the continuous stream breaks, stop timing and refer to the table below.
Add the appropriate solvent and continue testing until the proper thickness is reached for the type of material you are using.
Material
% of reduction
Time
Solvent
Projector Set
Latex ..............................20-25% ..................................30-35 sec. ............Water ............................................. 5
Oil ...................................10-20% ..................................20-30 sec. ............Mineral Spirits ................................ 4
Epoxy .............................1-10% ....................................30-35 sec. ............Mfg. Recommendations................. 5
Clear wood finish ............Full strength ........................................................Mfg. Recommendations................. 4
Varnish ...........................Mfg. Recommendations ......................................Naphtha ......................................... 3
Polyurethane ..................10% .......................................18-22 sec. ............M.E.K. ............................................ 3
Sealer .............................Full strength ........................................................Mineral spirits ................................ 3
Oil-based primer .............15-20% ..................................30-35 ....................Mineral spirits ................................ 4
Fast-dry enamel .............25% .......................................20-25 ....................Mineral spirits ................................ 4
Stain ...............................Full strength ........................................................Mfg. Recommendations................. 3
Metal primer ...................15% .......................................25-30 sec. ............Mineral spirits ................................ 4
Industrial enamel ............15% .......................................30-35 sec. ............Mineral spirits ................................ 4
Aluminum paint ..............Full strength ........................................................Mineral spirits ................................ 4
Lacquer sealer ...............Mfg. Recommendations ........18-22 sec. ............Lacquer thinner.............................. 3
Lacquer ..........................50% .......................................18-22 sec. ............Lacquer thinner.............................. 3
