background image

24

© Titan Tool Inc.  All rights reserved.

Patents

These products may be covered by one or more of the following U.S. patents:

4,457,472

4,508,268

4,494,697

4,500,119

4,611,758

4,744,571

4,768,929

5,425,506

5,749,528

5,947,381

Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment
covered by this warranty is free from defects in material and workmanship.  Titan’s obligation under this warranty is limited to
replacing or repairing without charge those parts which, to Titan’s reasonable satisfaction, are shown to be defective within
twelve (12) months with the exception of defects in the parts of the drive train/gear box or pressure control assembly which will
be repaired or replaced for twenty four months after sale to the End User.  This warranty applies only when the unit is installed
and operated in accordance with the recommendations and instructions of Titan.

This warranty does not apply in the case of damage or wear caused by abrasion, corrosion or misuse, negligence, accident,
faulty installation, substitution of non-Titan component parts, or tampering with the unit in a manner to impair normal operation.

Defective parts are to be returned to an authorized Titan sales/service outlet.  All transportation charges, including return to the
factory, if necessary, are to be borne and prepaid by the End User.  Repaired or replaced equipment will be returned to the End
User transportation prepaid.
THERE IS NO OTHER EXPRESS WARRANTY.  TITAN HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES
INCLUDING, BUT NOT LIMITED TO, THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO
THE EXTENT PERMITTED BY LAW.  THE DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS
LIMITED TO THE TIME PERIOD SPECIFIED IN THE EXPRESS WARRANTY.  IN NO CASE SHALL TITAN LIABILITY EXCEED
THE AMOUNT OF THE PURCHASE PRICE.  LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES
UNDER ANY AND ALL WARRANTIES IS EXCLUDED TO THE EXTENT PERMITTED BY LAW.

TITAN MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY TITAN.  THOSE ITEMS SOLD, BUT NOT MANUFACTURED BY TITAN (SUCH AS GAS ENGINES,
SWITCHES, HOSES, ETC.) ARE SUBJECT TO THE WARRANTY, IF ANY, OF THEIR MANUFACTURER.  TITAN WILL PROVIDE
THE PURCHASER WITH REASONABLE ASSISTANCE IN MAKING ANY CLAIM FOR BREACH OF THESE WARRANTIES.

Warranty

United States Sales & Service

1-800-526-5362

Fax 1-800-528-4826

556 Commerce Street

Franklin Lakes, NJ 07417

Canadian Branch

1-800-565-8665

Fax 1-905-856-8496

200 Trowers Road, Unit 7B

Woodbridge, L4L 5Z8

International

1-201-405-7520

Fax 1-201-405-7449

556 Commerce Street

Franklin Lakes, NJ 07417 USA

www.titan-tools.com

Summary of Contents for 440xc

























Reviews: