Titan 524093, Owner'S Manual

English

14

Troubleshooting

Problem

Cause

Solution

The unit will not run

  1.  The power cord is unplugged, or no power 

in outlet

  2.  Device overheated

  1.  Plug the power cord into 120V outlet

  2.  Unplug the power plug, let the device cool down 

approx. 30 minutes, check the air filter, do not cover the 

intake slots

Little or no material flow

  1.  Nozzle clogged

  2.  Suction tube clogged

  3.  Material flow setting too low

  4.  Suction tube loose

  5.  No pressure build-up in container

  6.  Container empty

  7.  Suction tube filter clogged (if applicable)

  8.  Air tube loose/damaged

  9.  Paint container seal damaged

 10.  Air vent on suction tube blocked

 11.  Air tube valve seal stuck

 12.  Air filter clogged

  1.  Clean

  2.  Clean

  3.  Increase flow

  4.  Insert

  5.  Tighten container

  6.  Refill

  7.  Clean or use another filter

  8.  Re-install or replace (see page 13)

  9.  Replace

 10.  Clean (see page 10)

 11.  Clean (see page 13)

 12.  Clean or replace

Material leaking

  1.  Air cap, nozzle or needle dirty

  2.  Front end assembly attachment incorrectly 

assembled

  3.  Nozzle loose

  4.  Nozzle seal worn

  5.  Nozzle worn

  6.  Needle worn

  7.  Material build-up on air cap and nozzle

  1.  Clean 

  2.  Assemble correctly (see page 12)

  3.  Tighten

  4.  Replace

  5.  Replace

  6.  Use new spray attachment

  7.  Clean

Spray pattern too thick, runs, spits 

and sags

  1.  Material flow setting too high

  2.  Air flow setting too low

  3.  Nozzle clogged

  4.  Air filter clogged

  5.  Too little pressure build-up in container

  6.  Viscosity of material too high

  7.  Air tube loose/damaged

  8.  Activating the trigger too quickly

  9.  Applying too much material

 10.  Distance from the spray object too small

 11.  Front end assembly not suitable for spray 

material

  1.  Decrease flow setting

  2.  Increase air flow setting

  3.  Clean

  4.  Clean or replace (see page 13)

  5.  Tighten container

  6.  Thin

  7.  Re-install or replace

  8.  Pull trigger partially until turbine reaches full power

  9.  Decrease volume setting or increase movement of spray 

gun

 10.  Increase distance to spray object

 11.  Use a different front end assembly

Spray jet pulsates

  1.  Material in container running out

  2.  Air filter clogged

  3.  Nozzle seal worn

  4.  Suction tube loose

  5.  Suction tube / suction tube filter clogged

  1.  Refill

  2.  Clean or replace (see page 13)

  3.  Replace

  4.  Insert

  5.  Clean or use another filter

Too much overspray

  1.  Gun too far from spray object

  2.  Too much material applied

  3.  Air flow setting too high

  4.  Material has been over-thinned

  5.  Front end assembly not suitable for spray 

material

  1.  Reduce distance

  2.  Decrease material flow setting

  3.  Decrease air flow setting

  4.  Thicken the material by adding more material

  5.  Use a different front end assembly

Paint in the air tube

  1.  Valve seal dirty

  2.  Valve seal defective

  1.  Clean the valve seal (see page 13)

  2.  Replace the valve seal (see page 13)

any attempt to open the motor housing or repair any electrical 

parts within the unit by anyone other than an authorized repair 

technician could cause serious injury and will void the warranty.

This unit contains no servicable electrical parts.  Do 

not attempt to service yourself.  Store indoors with 

the power cord wrapped and secured with the velcro 

strap.