background image

© Titan Tool Inc.  All rights reserved. 

3

English

haZaRD:  EXPLOSION haZaRD DuE TO 

INcOMPaTIBLE MaTERIaLS 

Will cause property damage or severe injury.

PREvENTION:

 

•  Do not use materials containing bleach or chlorine.

 

•  Do not use halogenated hydrocarbon solvents such as bleach, 

mildewcide, methylene chloride and 1,1,1 - trichloroethane.  They 

are not compatible with aluminum.

 

•   Contact your coating supplier about the compatibility of material 

with aluminum.  

haZaRD:  GENERaL 

Can cause severe injury or property damage.

PREvENTION:

 

•  Read all instructions and safety precautions before operating 

equipment.

 

•  Follow all appropriate local, state, and national codes governing 

ventilation, fire prevention, and operation. 

 

•  The United States Government Safety Standards have been 

adopted under the Occupational Safety and Health Act (OSHA).  

These standards, particularly part 1910 of the General Standards 

and part 1926 of the Construction Standards should be consulted.

 

•  Use only manufacturer authorized parts.  User assumes all risks 

and liabilities when using parts that do not meet the minimum 

specifications and safety requirements of the pump manufacturer.

 

•  All hoses, fittings, and filter parts must be secured before 

operating spray pump.  Unsecured parts can eject at great force 

or leak a high pressure fluid stream causing severe injury.

 

•  Before each use, check all hoses for cuts, leaks, abrasion or 

bulging of cover.  Check for damage or movement of couplings. 

Immediately replace the hose if any of these conditions exist.  

Never repair a paint hose. Replace it with another grounded high-

pressure hose.

 

•  Do not kink or over-bend the hose. Airless hose can develop 

leaks from wear, kinking and abuse.  A leak can inject material 

into the skin.  

 

•  Do not expose the hose to temperatures or pressures in excess of 

those specified by manufacturer.

 

•  Do not spray outdoors on windy days.

 

•  Wear clothing to keep paint off skin and hair.

 

•  Do not operate or spray near children.  Keep children away from 

the equipment at all times.

 

•  Do not overreach or stand on an unstable support.  Keep effective 

footing and balance at all times.

 

•  Use lowest possible pressure to flush equipment.

 

•  Stay alert and watch what you are doing.

 

•  Do not operate the unit when fatigued or under the influence of 

drugs or alcohol.

 

•  For electric units — Always unplug cord from outlet before 

working on equipment.

 

•  Do not use the hose as a strength member to pull or lift the 

equipment.

 

•  Do not lift by cart handle when loading or unloading.

Table of contents

Safety Precautions ................................................................ 2-3

Introduction ............................................................................... 4

Preparation................................................................................ 5

Operation ................................................................................ 5-6

cleanup ..................................................................................... 6

Maintenance .............................................................................. 7

Troubleshooting ....................................................................... 7

Parts List ................................................................................. 20

Specifications

Maximum air input pressure ............

115 PSI (0.79 MPa)

Maximum working pressure

.............

3600 PSI (24.8 MPa)

Air connector  ..................................

QD Nipple

Material connector ........................... NPSM 1/4”

Filter, standard.................................

100 mesh (see chart on page 

7 for available filter sizes)

Length

..............................................

8.5” (216 mm)

Height

 ..............................................

9.8” (250 mm)

Weight

 .............................................

1 lb. (420 g)

Reversible Tip Spray Gun

 ...............

P/N 0524357

Flat Tip Spray Gun

 .......................... P/N 0524358

Summary of Contents for CAPSpray GM3600

























Reviews: