© Titan Tool Inc. All rights reserved.
9
5. Open the hydraulic shut-off valve located on the hydraulic
pressure hose. The handle should be in line with the
hose.
6. Open the bleed valve by turning the bleed valve knob fully
counterclockwise.
7. Start the engine or turn on the electric motor.
Fuel Valve
Lever
Choke Lever
Engine
Switch
Throttle
Lever
Starter Rope
a. To start the gas
engine,
• move the fuel valve
lever to the open
position,
• move the throttle
lever to its middle
point,
• move the choke lever
to the closed position
for a cold engine or
to the open position
for a warm engine,
• turn the engine switch to the ON position, and
• pull the starter rope briskly until the engine starts.
b. To start the electric motor, move the ON/OFF switch to
the ON position.
8. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and material flows freely from the bleed
hose.
9. Turn off the sprayer.
a. To turn off the gas engine,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the throttle lever to the slow position, and
• turn the engine switch to the OFF position.
b. To turn off the electric motor,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the ON/OFF switch to the OFF position.
10. Remove the bleed hose from the waste container and
place it into the container of material.
11. Close the bleed valve by turning the bleed valve knob fully
clockwise.
12. Start the engine or turn on the electric motor.
13. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure.
14. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
15. Trigger the gun into the metal waste container until all air
and solvent is flushed from the spray hose and material is
flowing freely. from the gun.
Trigger lock in
locked position.
15. Lock the gun by turning the gun trigger
lock to the locked position.
16. Lock the gun by turning the gun trigger
lock to the locked position.
17. Turn off the sprayer.
18. Attach tip guard and tip to the gun
as instructed by the tip guard or tip
manuals.
POSSIBLE INJEcTION haZaRD. Do not spray
without the tip guard in place. Never trigger the
gun unless the tip is in either the spray or the
unclog position. always engage the gun trigger
lock before removing, replacing or cleaning tip.
NOTE: When spraying textured products, the use
of a splatter nozzle on the spray gun may be
necessary. The splatter nozzle adds atomizing
air to the fluid stream to create the desired
material consistency. Refer to the Splatter
Nozzle Instruction Sheet (P/N 313-2468) for
detailed instructions.
19. Start the engine or turn on the electric motor.
20. Increase the pressure by turning the pressure control knob
slowly clockwise and test the spray pattern on a piece
of cardboard. Adjust the pressure control knob until the
spray from the gun is completely atomized.
NOTE: Turning the pressure up higher then needed to
atomize the material will cause premature tip
wear and additional overspray.
Pressure Relief Procedure
Be sure to follow the Pressure Relief Procedure
when shutting the unit down for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray nozzles,
or preparing for cleanup.
Trigger lock in
locked position.
1. Lock the gun by turning the gun trigger
lock to the locked position.
2. Turn off the sprayer.
a. To turn off the gas engine,
• set the pressure to minimum by
turning the pressure control knob
fully counterclockwise,
• move the throttle lever to the slow
position, and
• turn the engine switch to the OFF position.
b. To turn off the electric motor,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the ON/OFF switch to the OFF position.
3. Close the hydraulic shut-off valve on the hydraulic
pressure hose.
4. Unlock the gun by turning the gun trigger lock to the
unlocked position.
5. Hold the metal part of the gun firmly to the
side of a metal waste container to ground
the gun and avoid a build up of static
electricity.
6. Trigger the gun to remove any pressure
that may still be in the hose.
7. Lock the gun by turning the gun trigger lock to the locked
position.
8. Place the bleed hose into the metal waste container.
9. Open the bleed valve by turning the bleed valve knob fully
counterclockwise.
