TitanCut 40
PFC
Operators Manual
Issue. A 0516
power supply.
Work cable not connected to work piece, or connection is poor, make sure that work cable has a
proper connection to a clean, dry area of the workpiece.
Faulty components in unit, return for repair or have qualified technician repair per Service
Manual.
Faulty Torch, return for repair or have qualified technician repair.
8.
Low cutting output
Incorrect setting of CURRENT (A) control, check and adjust to proper setting.
Faulty components in unit, return for repair or have qualified technician repair.
9.
Difficult Starting
Worn torch parts (consumables), shut off input power. Remove and inspect torch shield cup, tip
and electrode. Replace electrode or tip if worn; replace shield cup if excessive spatter adheres
to it.
10.
Arc shuts off during operation; arc will not restart when torch switch is activated.
Power Supply is overheated (OC/OT lamp on), let unit cool down for at least 5 minutes. Make
sure the unit has not been operated beyond Duty Cycle limit. Refer to Section 2 for duty cycle
specifications.
Gas pressure too low (the TIP/GUN/GAS lamp on when press on torch switch is on), check
source for at least 4bar/60psi; adjust as needed.
Torch consumables worn, check torch shield cup, tip, starter element, and electrode; replace as
needed.
Faulty components in unit:, return for repair or have qualified technician repair per Service
Manual.
11.
No gas flow; the power lamp on; Fan operates
Gas not connected or pressure too low, check gas connections. Adjust gas pressure to proper
setting.
Faulty components in unit, return for repair or have qualified technician repair.
12.
Torch cuts but low quality
Current (A) control set too low, increase current setting.
Torch is being moved too fast across workpiece, reduce cutting speed.
Excessive oil or moisture in torch, hold torch 1/8 inch (3 mm) from clean surface while purging
and observe oil or moisture buildup (do not activate torch). If there are contaminants in the
gas, additional filtering may be needed.
Summary of Contents for 40 PFC
