background image

 

 

875240 

HDBaseT

 /HDMI Splitter 1x4 

TLS electronics GmbH                                                                                            Contact: info@tls-electronics.de   2 

 

 

 

Thank you for purchasing this product. For optimum performance and 
safety, please read these instructions carefully before connecting, 
operating or adjusting this product. Please keep this manual for future 
reference.   

 

 

SURGE PROTECTION DEVICE RECOMMENDED 

This  product  contains  sensitive  electrical  components  that  may  be 
damaged  by  electrical  spikes,  surges,  electric  shock,  lightning  strikes, 
etc. Use of surge protection systems is highly recommended in order to 
protect and extend the life of your equipment.   
 

 

SAFETY AND NOTICE 

1.  The transmission distances of HDMI over UTP cables are measured 

using TE CONNECTIVITY 1427071-6   

2.  EIA/TIA-568-B termination (T568B) for CAT cables (AWG 24/1) is 

recommended for better performance

3.  DO NOT use 568A/568B standard mixed CAT cable (cross-over 

cable) because there are 2 pairs swapped, this will make POE 
OVER-CURRENT and damage POE components. Please use 
straight-through CAT cable (both RJ45 headers are 568A or 568B 
standard). 

4.  It is recommended that power up the device after connections of 

source, sink and CAT cable. 

5.  To reduce the interference among the unshielded twisted pairs of 

wires in CAT cable, do not run HDBaseT / Zone Cat5e/6/6a cabling 
with or in close parallel proximity to mains power cables. Shielded 
CAT cables can be used to improve EMI problems, which is worsen 
in long transmission.   

6.  Because the quality of the CAT cables has the major effect on how 

long the transmission limit can achieve and how good is the received 
picture quality, the actual transmission range is subject to one’s 
choice of CAT cables.   

7.  Do not substitute or use any other Power Supply other than the 

enclosed unit, or a TLS approved Replacement Part. Doing so 
will void the warranty and potentially expose the user to 
dangerous voltages resulting in an electrical shock.   

8.  Do not disassemble the device for any reason. Doing so will void the 

manufacturer’s warranty. Also, our unique case is an integral part of 

Summary of Contents for 875240












Reviews: