B. Programming of System
Function
Group
Function
Func-
tion
Code
Remarks
The following standard station numbering schedules of the
exchanges A, B and C are obtainable. (Hardwired station number)
Numbering Schedules of
Tie-line System
Selectable first station
number of each
exchange
The first station number of each exchange in order of the
exchanges. A, B and C can be set as any of the following numbers:
100/200/300/400/500/600/700/800/900
(Hardwired station number)
Call tone selection
Two different calling tones, single note tone or trill note tone, are
available in selection for the Hands-free system except the
continuous calling tone.
Selection of Paging
Pre-announcement
Tone Duration
You can select the length of time of paging pre-announcement tone.
Single-digit dialling key
selection
It is possible to operate the single-Digit Dialling with any other dial
key than
Selection of 1st digit of
4-digit dialling
Program the 1st digit for a local exchange under 4-digit dialling,
choosing from among the following schedules:
2000/3000/4000/5000/6000/7000/8000/9000
Time-out Conversation
Programming is possible so that stations can be disconnected
automatically from the speech path in the unit of Minut and the
Hurry-up Signal Tone can be heard 10 seconds before the
disconnection.
Time-out Paging Call
Programming is possible so that stations can be disconnected
automatically from the Paging circuit in the unit of Minute and the
Hurry-up Signal Tone can be heard 10 seconds before the
disconnection.
Pager call output digit
selection
Pager call function code
output mode selection
The number of digits in length may be selected to call a pager.
Function code transmission order may be selected according to the
type of pager.
Pre-pause time setting
It is possible to set pre-pause time of OD-600, LD-600 and CB-600.
Number of SM-600 units
connected
Program the number of the SM-600 units to be connected.
Message recording hurry-
up tone mode selection
A Hurry-up tone may be transmitted 2 seconds before the
programmed recording time in up.
Operating for Programming
First Station No.
of Exchange "A"
1-9 (First digit)
First Station No.
of Exchange "B"
2-9 (First digit)
First Station No.
of Exchange "C"
3-9 (First digit)
0: Without Calling Tone
1: Single Note Tone (0.2 sec.)
2: Trill note Tone (0.3 sec.)
0: Without Paging pre-announcement Tone
1: Paging Pre-announcement Tone (1 sec.)
2: Paging Pre-announcement Tone (2 sec.)
Initially
Programmed
Mode
Standard Station
Numbering
A/B/C=
200/470/740
(SW-D-5 OFF)
or
A/B/C=
200/500/800
(SW-D-5ON)
Trill note Tone (0.3 sec.)
Paging
Pre-announcement Tone
(2 sec.)
00: Without Time-out function
01-99: Length limited (minute)
Without
Time-out
Without
Time-out
00: Without Time-out function
01-99: Length limited (minute)
0: 2 digits
1: 3 digits 2: 4 digits
2 digits
0: Output before pager number
1: Output after pager number
2: No output
Output before pager number
0: 0.06 sec., 1: 1 sec., 2: 1.5 sec., 3: 2 sec., 4: 2.5 sec., 5: 3 sec., 6: 3.5 sec., 7: 4 sec., 8: 4.5 sec., 9: 5 sec
0.6 sec.
0: No unit connected
1 ~4: Number of units connected
No unit connected
0: Hurry-up tone is transmitted
1: No Hurry-up tone
Hurry-up tone is transmitted
— 18 —
All manuals and user guides at all-guides.com
