background image

2

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe 

operation.

•  Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or 

cautions regarding safety.

•  After reading, keep this manual handy for future reference.

•  Avoid touching the unit's sharp metal edge to prevent injury.

•  Use the 12 V DC power supply and PoE switching hub for the unit. Note that the use of another adapter and 

PoE switching hub may cause a fire. (N-SP80VS1 and N-SP80AS1 only)

Indicates a potentially hazardous situation which, if mishandled, could 

result in moderate or minor personal injury, and/or property damage.

CAUTION

FCC REQUIREMENTS

Note

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 

interference in a residential installation. This equipment generates, uses and can radiate radio frequency 

energy, and if not installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 

one or more of the following measures:

•  Reorient or relocate the receiving antenna

•  Increase the separation between the equipment and receiver

•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•  Consult the dealer or an experienced radio/TV technician for help

Modifications

Any modifications made to this device that are not approved by TOA Corporation may void the authority 

granted to the user by the FCC to operate this equipment.

Summary of Contents for N-SP80AS1









Reviews: