background image

Quick Start Guide 

Page 8 of 8 

Cross Check Data 

Always cross check the data displayed on the scanner versus what is shown on the 
front of the ID.  Some fake IDs have a 'cloned' or copied data stripe from another 
person who is over 21 years old.   

 

The "F.E.A.R." method of carding from the PA Liquor Control Board. 

1.  FEEL FOR: 

* Glue line or bumpy surfaces by the picture or birth date. 
* Pin holes on the surface. 
* Thickness of an ID. If it's been re-laminated, it may be thicker.  

2.  EXAMINE: 

* The photo and physical description. They should match the person handing you the ID. 
* The expiration date. You CANNOT accept an expired ID. 
* The birth date. Do your math. Are they 21? 
* Whether or not the ID is a duplicate. If it is, ask for another form of ID. 
* The state logo. If it's partially missing or appears altered, the ID might be fake. 
* The hologram. Is it a genuine hologram or a basic hologram added to a fake ID? 
* The card's reverse side lettering. Some ID-makers neglect the back side of the ID. Look for 
blurred lettering or a cut out piece of paper. 
* Whether it is an out-of-state license. Use an ID checking guide when you're looking at an 
unfamiliar license.  

3.  ASK: 

* About basic information on the card, such as the birth date, middle initial, zip code, age, etc. 
* For a second form of ID. People with fakes rarely carry back-up identification. 

4. 

RETURN: 
* If you are satisfied that the proof of age is valid, you may permit the individual to be served. 
* If you're not convinced, however, do not serve them.

  

Summary of Contents for IDVisor Touch









Reviews: