background image

CCD Monochrome

Video Camera

CS8320B (E I A )
CS8320BC (CCIR)

Operation Manual

 

TOKYO ELECTRONIC INDUSTRY CO.,LTD:

For customer Use 

Enter below the Serial No. which is located on the bottom  

chassis of the camera. 

Retain this information for future reference, 

Model No. CS 

Serial No. 

 

 

 

CAUTION 

To prevent electric shock, do not use the polarized plug of the  

AC Power adapter with an extension cord, receptacle or other  
outlet unless the blades can be fully inserted to prevent blade  
exposure. 
 

When the camera is used within an electromagnetic field, beat 

interference (vertical, horizontal or diagonal stripes) may be  
created in the video output. If this occurs, take measures on the  
source of the electromagnetic waves to prevent the emissions  
from affecting the video output. 

Such measures are particularly necessary on systems with  

servo motors, inverters and other equipment that tends to  
generate electromagnetic waves. 
 

Do not subject the camera to strong shocks, as this may result  

in failure or breakage. 

When the camera is used on systems which subject the camera  

connector to strong shocks, the camera connector may suffer  
damage. If the camera is used on such systems, the connector  
plug should be fastened to the camera with the optional camera  

connector bracket. 

Summary of Contents for CS8320B
















Reviews: