background image

60

Tone Commander 6210/6220 User Manual

Ringing Control for Individual Call Appearances

You can control the audible ringing at your telephone for each call
appearance.

Call appearances set to ALWAYS will ring immediately. Use this setting
for your primary call appearances.

NEVER completely disables ringing on the call appearance. Use this
selection for monitored call appearances that are normally answered
elsewhere.

WAIT delays ringing at your telephone for 2 to 7 ringing cycles (6
seconds per cycle). Use this option for backup answering on call
appearances that are primarily answered on other terminals.

Calls that do not ring, due to the ringing control selection, do not
display call information and are not recorded in the call log.

 From the User Options menu, select RING.
(

Setup

 

 USER

 

 RING)

Select CONTROL.
All multifunction keys that are programmed for call
appearances or DSS will have a steady green indication.

Press a lit key to view its current ring control setting.

If you want to change the setting for the selected key, select
ALWAYS, NEVER, or WAIT2-WAIT7.

Press the 

Done

 key to return to the Personal Ringing menu or

the 

Setup

 key to exit Setup Mode.

Done

KEY01=ALWAYS RING      \
ALWAYS NEVER WAIT2 WAIT3

KEY01=ALWAYS RING      \
WAIT4 WAIT5 WAIT6  WAIT7

Summary of Contents for 6210























































































Reviews: